Detailed instructions for use are in the User's Guide.
[. . . ] Otherwise electric shock may occur.
10 cm 10 cm 10 cm 10 cm
Using the cable holder
2 Connect the AC-DC Adapter and Power Cord
to a wall outlet.
Cable holder
or
ASSEMBLING AND PREPARING
7
WARNING
When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.
Using the Kensington security system The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit http://www. kensington. com. Connect the Kensington security system cable between the Monitor set and a table.
ENG ENGLISH
Do not touch or press the screen when adjusting the angle of the monitor.
Do not hold this set like below picture. Monitor screen can detach from stand base and injure your body.
NOTE
The Kensington security system is optional. You can obtain it from most electronics stores.
NOTE
Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.
Front
Rear
8
ASSEMBLING AND PREPARING
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. [. . . ] · When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. · When only one signal is connected, it is automatically detected. Power Indicator The power indicator stays red if the display is running properly (On Mode). If the display is in Sleep Mode, the power indicator blinks red.
12
CUSTOMIZING SETTINGS
Customizing Settings
ENGLISH ENG
Menu Settings
1 Press MENU button on the bottom of the Monitor set
to display the MENU OSD. buttons.
2 Set the options by pressing the or or 3 Select the "NEXT MENU" button to enter the more
option settings.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
Each option is explained below.
MENU BRIGHTNESS CONTRAST WIDE/ORIGINAL Analog Digital Description To adjust the brightness, contrast of the screen WIDE Switch to full screen mode according to input image signal. * This function works only if input resolution is lower than Monitor set ratio (16:9). Press the , buttons to reset immediately.
MENU > NEXT MENU PICTURE COLOR DISPLAY SHARPNESS GAMMA COLOR TEMP HORIZONTAL VERTICAL CLOCK PHASE OTHERS LANGUAGE POWER INDICATOR WHITE BALANCE
Analog Digital
Description To adjust the clearness of the screen . To customize the color of the screen To adjust the position of the screen To improve the clarity and stability of the screen To customize the screen status for a user's operating environment
y Analog: D-SUB(Analog signal) input. y Digital: DVI-D(Digital signal) input.
CUSTOMIZING SETTINGS
13
PICTURE ENG ENGLISH
1 Press MENU button on the bottom of the Monitor set
to display the MENU OSD. option settings.
2 Select the "NEXT MENU" button to enter the more 3 Enter to PICTURE by pressing the button. option settings.
2 Select the "NEXT MENU" button to enter the more 3 Select OTHERS by pressing the button. 5 Set the options by pressing the or or
buttons.
6 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow ( ) button. Each option is explained below.
MENU > NEXT MENU > OTHERS LANGUAGE POWER INDICATOR WHITE BALANCE Description To choose the language in which the control names are displayed. Use this function to set the power indicator on the bottom side of the monitor to ON or OFF. If you set OFF, it will go off. If you set ON at any time, the power indicator will automatically be turned on. If the output of the video card is different the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image. Activate this function when white and black colors are present in the screen.
CUSTOMIZING SETTINGS
17
SUPER ENERGY SAVING Setting
ENG ENGLISH
1 Press
( SUPER ENERGY SAVING ) button on the bottom of the Monitor set to display the SUPER ENERGY SAVING OSD.
2 Set the options by pressing the or or buttons. 3 Select EXIT to leave the OSD menu.
Each option is explained below.
SUPER ENERGY SAVING ON OFF RESET Description Enables SUPER ENERGY SAVING you can save energy with this energy- efficient function Disables SUPER ENERGY SAVING. Resets the values of total energy consumption reduction and CO2 emission reduction estimates.
NOTE
y TOTAL POWER REDUCTION: How much power is saved while using the monitor. y SAVING DATA(W/h) 470 mm (18. 5 inch) SUPER SAVING 4 W/h 508 mm (20 inch) 5 W/h 546 mm (21. 5 inch) 6 W/h 584 mm (23 inch) 7 W/h 609 mm (24 inch) 7 W/h
y Saving Data depends on the Panel. y LG calculated these values by using "broadcast video signal" (including broadcast video: IEC 62087) y SUPER SAVING refers to how much power can be saved using the SUPER ENERGY SAVING function.
18
CUSTOMIZING SETTINGS
PICTURE MODE Setting
ENGLISH ENG
1 Press MODE button on the bottom of the Monitor set to display the PICTURE MODE OSD . 3 Select EXIT to leave the OSD menu.
Each option is explained below.
PICTURE MODE CUSTOM TEXT PHOTO CINEMA GAME Description It is a mode that the user can adjust each element. [. . . ] Digital 15 pin D-SUB Connector /DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital D-SUB(Analog) : 1600 x 900 @ 60 Hz DVI (Digital) : 1600 x 900 @ 60 Hz VESA 1600 x 900 @ 60 Hz
Dimensions (Width x Height x Depth) Weight Tilt Range Environmental conditions
OUTPUT: 19 V With Stand Without Stand 2. 3 kg -5° to 20°
1. 3 A 47. 4 cm x 36. 6 cm x 16. 8 cm 47. 4 cm x 29. 2 cm x 5. 5 cm
Operating Temperature 10°C to 35 °C Operating Humidity 10 % to 80 % Storage Temperature Storage Humidity -20°C to 60 °C 5 % to 90 % non-Condensing
Stand Base Power cord
Attached ( ), Detached (O) Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
24
SPECIFICATIONS
SPECIFICATIONS
E2242S
Display Screen Type Pixel Pitch Horizontal Frequency Vertical Frequency Input Form Signal Input Input Form Max Recommend DDC 2B(Analog) On Mode : 23 W(Typ. ) Sleep Mode 0. 3 W Off Mode 0. 3 W 1. 2 A 19 V
Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE
ENGLISH ENG
Sync Input
Video Input Resolution Plug & Play Power Consumption Power Input AC-DC Adapter
54. 6 cm (21. 5 inch) Flat Panel Active matrix-TFT LCDAntiGlare coating Visible diagonal size: 54. 6 cm 0. 247 mm x 0. 247 mm (Pixel Pitch) 30 kHz to 83 kHz (Automatic) 56Hz to 75Hz (D-SUB) Separate Sync. 15 pin D-SUB Connector RGB Analog (0. 7 Vp-p/ 75 ohm) D-SUB(Analog) : 1920 x 1080 @ 60 Hz VESA 1920 x 1080 @ 60 Hz
Dimensions (Width x Height x Depth) Weight Tilt Range Environmental conditions
OUTPUT: 19 V With Stand Without Stand 2. 6 kg -5° to 20°
1. 3 A 50. 9 cm x 38. 7 cm x 18. 1 cm 50. 9 cm x 31. 3 cm x 5. 5 cm
Operating Temperature 10°C to 35 °C Operating Humidity 10 % to 80 % Storage Temperature Storage Humidity -20°C to 60 °C 5 % to 90 % non-Condensing
Stand Base Power cord
Attached ( ), Detached (O) Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
SPECIFICATIONS
25
SPECIFICATIONS
E2242T
Display Screen Type Pixel Pitch Horizontal Frequency Vertical Frequency Input Form Signal Input Input Form Max Recommend Plug & Play Power Consumption Power Input AC-DC Adapter DDC 2B(Analog, Digital) On Mode : 23 W(Typ. ) Sleep Mode 0. 3 W Off Mode 0. 3 W 1. 2 A 19 V
Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE
ENG ENGLISH
54. 6 cm (21. 5 inch) Flat Panel Active matrix-TFT LCDAntiGlare coating Visible diagonal size: 54. 6 cm 0. 247 mm x 0. 247 mm (Pixel Pitch) 30 kHz to 83 kHz (Automatic) 56Hz to 75Hz (D-SUB, DVI-D) Separate Sync. Digital 15 pin D-SUB Connector /DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital D-SUB(Analog) : 1920 x 1080 @ 60 Hz DVI (Digital) : 1920 x 1080 @ 60 Hz VESA 1920 x 1080 @ 60 Hz
Sync Input
Video Input Resolution
Dimensions (Width x Height x Depth) Weight Tilt Range Environmental conditions
OUTPUT: 19 V With Stand Without Stand 2. 6 kg -5° to 20°
1. 3 A 50. 9 cm x 38. 7 cm x 18. 1 cm 50. 9 cm x 31. 3 cm x 5. 5 cm
Operating Temperature 10°C to 35 °C Operating Humidity 10 % to 80 % Storage Temperature Storage Humidity -20°C to 60 °C 5 % to 90 % non-Condensing
Stand Base Power cord
Attached ( ), Detached (O) Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
26
SPECIFICATIONS
SPECIFICATIONS
E2342T
ENGLISH ENG
Display Screen Type Pixel Pitch Horizontal Frequency Vertical Frequency Input Form Signal Input Input Form Max Recommend DDC 2B(Analog, Digital) On Mode : 24 W(Typ. ) Sleep Mode 0. 3 W Off Mode 0. 3 W 1. 3 A 19 V 58. 4 cm (23 inch) Flat Panel Active matrix-TFT LCDAntiGlare coating Visible diagonal size: 58. 4 cm 0. 265 mm x 0. 265 mm (Pixel Pitch) 30 kHz to 83 kHz (Automatic) 56Hz to 75Hz (D-SUB, DVI-D) Separate Sync. Digital 15 pin D-SUB Connector /DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital D-SUB(Analog) : 1920 x 1080 @ 60 Hz DVI (Digital) : 1920 x 1080 @ 60 Hz VESA 1920 x 1080 @ 60 Hz
Sync Input
Video Input Resolution
Plug & Play Power Consumption Power Input AC-DC Adapter
Type ADS-40SG-19-3 19032G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE
OUTPUT: 19 V
1. 7 A
Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE
Dimensions (Width x Height x Depth) Weight Tilt Range Environmental conditions
OUTPUT: 19 V With Stand Without Stand 2. 9 kg -5° to 20°
1. 3 A 54. 4 cm x 40. 6 cm x 18. 1 cm 54. 4 cm x 33. 2 cm x 5. 5 cm
Operating Temperature 10°C to 35 °C Operating Humidity 10 % to 80 % Storage Temperature Storage Humidity -20°C to 60 °C 5 % to 90 % non-Condensing
Stand Base Power cord
Attached ( ), Detached (O) Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
SPECIFICATIONS
27
SPECIFICATIONS
E2442T
Display Screen Type Pixel Pitch Horizontal Frequency Vertical Frequency Input Form Signal Input Input Form Max Recommend Plug & Play Power Consumption Power Input AC-DC Adapter DDC 2B(Analog, Digital) On Mode : 25 W(Typ. ) Sleep Mode 0. 3 W Off Mode 0. 3 W 1. 6 A 19 V
Type ADS-40SG-19-3 19032G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE
ENG ENGLISH
Sync Input
Video Input Resolution
60. 9 cm (24 inch) Flat Panel Active matrix-TFT LCDAntiGlare coating Visible diagonal size: 60. 9 cm 0. 277 mm x 0. 277 mm (Pixel Pitch) 30 kHz to 83 kHz (Automatic) 56Hz to 75Hz (D-SUB, DVI-D) Separate Sync. [. . . ]