User manual LA CROSSE TECHNOLOGY WT5160

[. . . ] · The indoor temperature and the time as 0 :00 will be displayed. · The DCF time reception will automatically be initiated, and a tower icon will appear (no tower icon will appear if the time reception is too weak to be detected, and the time display will start from 0:00). · When DCF time has not been received, user may use the MODE/MIN key to manually enter a time and date initially. The clock will automatically attempt to receive the DCF time at each full hour. [. . . ] In extreme cases, please place the unit close to a window and/ or point its front or back towards the Frankfurt transmitter. During nighttime, the atmospheric disturbances are usually less severe and reception is possible in most cases. A single daily reception is adequate to keep the accuracy deviation below 1 second. FUNCTION KEYS The radio-controlled Projection clock uses the following keys : SNOOZE button · 38 AL / HOUR button MODE/ MIN button Projection Direction button SNOOZE : · Activate or deactivate snooze function · Alarm snooze function · Activate the projection of time · Exit the setting modes · Back light on 39 AL/HOUR : · Set the hours and day · Activate or desactivate alarm · Enter alarm setting mode · Stop alarm and snooze function · Back light on MODE/MIN : · Enter manual time setting mode · Set the minutes, weekday and month · Enter time zone · Stop alarm and snooze function · Back light on PROJECTION DIRECTION : Project the image direction (can display 4 different orientations) · 40 · Back light on MANUAL SETTING Time zone setting User shall first remove all the batteries from the projection clock and wait for 3 minutes. Then user shall press and hold the MODE/MIN key and at the same time place the batteries into the clock. Then there will be a beep sound and the flashing time zone digits "0 h" will be displayed. User may now press shortly the MODE/MIN key to set the time zone between +9 and -9 hours (The time zone default of the Projection clock is "0 hour"). flashing 41 Then confirm with the SNOOZE key and enter the Manual time setting. Note: If AC adaptor is used instead of battery, user shall first connect the adaptor to the wall socket, then press and hold the MODE/MIN key and finally insert the power cable to the jack of the clock. User shall keep on holding the MODE/MIN key until the time zone flashing digit "0h" is displayed on LCD. Manual time setting In case the Projection clock cannot detect the DCF-signal (for example due to disturbances, transmitting distance, etc. ), the time can be manually set. The clock will then work as a normal Quartz clock. Hour flashing Minutes flashing 42 1. Note: · The unit will still try and receive the signal every one hour despite it being manually set. When it does receive the signal, it will change the manually set time into the received time. Also the manually-set date and weekday will be changed to the received date. Once the radiocontrolled time signals are received, the date is automatically updated. However, if the signals are not received, the date can also be set manually. Use the MODE/MIN key to set the year (the range runs from 2000 to 2049). 43 flashing 2. 3. Press the MODE/MIN key to set the year (between year 2000-2049). Press the SNOOZE key again to confirm and to enter the month and day setting. The month and day digits will start flashing. Day (flashing) Month (flashing) 44 4. 5. Press the AL/HOUR key to set the day and MODE/MIN key to set the month. Press the SNOOZE key again to confirm and to enter the Weekday setting mode. 7. Use the MODE/MIN key to set the weekday (Mo, Tu, We, Th, Fr, Sa or Su). [. . . ] The LED backlight cannot be turned on constantly; this would drain the batteries. MAINTENANCE: · Avoid placing the alarm clock in areas prone to vibration and shock as this may damage and inaccurate readings. · Avoid exposure to sudden changes in temperature such as direct sunlight, extreme cold and wet or moist conditions. · When cleaning the display and casing, only use a soft damp cloth. [. . . ]