User manual LA CROSSE TECHNOLOGY WS-9032U

[. . . ] WS-9032U Wireless 433 MHz Weather Station Instruction Manual FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter) FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. R Contents Language English French Spanish Page 2 23 46 TABLE OF CONTENTS Topic Inventory of Contents/ Additional Equipment About WWVB Quick Set Up Guide Detailed Set Up Guide Battery Installation Start Up Sequence Explanation of LCD Information Function Key Layout Program Mode Overview of Programming Sequence LCD Contrast Setting Time Zone Setting DST ON/OFF Setting Radio-controlled Time ON/OFF Setting 12/24-hour Time Mode Setting Setting the Time/Date Manually Temperature Measuring Units (°F/°C) Air Pressure Measuring Units (inHg/hPa) Relative Pressure Setting Forecast Sensitivity Setting Features and Operation Time Alarm Setting and Operation Moon Phase Minimum/Maximum Temperature/Humidity Multiple Remote Temperature/Humidity Sensors Comfort Icon Weather Forecast and Pressure Trend Indicators Weather Icons Weather Tendency Arrows Barometric Air Pressure Reading Air Pressure History Bar Chart Mounting Maintenance and Care Troubleshooting Guide Specifications Warranty Information Page 3 3 4 4 6 7 8 8 8 8 9 9 9 9 11 11 11 11 12 13 13 14 15 15 15 16 16 16 17 18 19 20 20 INVENTORY OF CONTENTS REMOTE THERMO-SENSOR 433 MHz 1. Instruction manual and warranty card ADDITIONAL EQUIPMENT (not included) 1. [. . . ] Press and release either of the SNOOZE/CH buttons to confirm the setting or wait for 20 seconds and the display will automatically return to the normal mode. Press and release the ALM/DATE button to toggle between the alarm time and the day and date. When the alarm time and alarm icon are showing to the right of the moon phase the alarm is activated. When the day and date are showing in the DATE LCD the alarm is deactivated. To deactivate the snooze function press and release any button other than either of the SNOOZE/CH buttons. C. Indoor Minimum and Maximum Temperature and Humidity The indoor weather station automatically stores the minimum and maximum indoor temperature and humidity. The minimum and maximum values are updated automatically when a new minimum or maximum is recorded, or until manually reset. From the normal display mode, press and release the "IN" key once to view the indoor maximum temperature and humidity ("MAX" will be displayed above the indoor temperature and humidity). Press and release the "IN" key again to view the indoor minimum temperature and humidity. Press and release the "IN" key again to return to the normal mode (timeout of viewing minimum/maximum values will occur if no keys are pressed for fifteen seconds). Note: To reset the indoor minimum and maximum temperature and humidity, first display the values you wish to reset (minimum or maximum). Next press and hold the "SET" key for at least three seconds. You will see then that the values will reset to the current temperature and humidity and corresponding time. 2. Outdoor Minimum and Maximum Temperature and Humidity The indoor weather station automatically stores the minimum and maximum outdoor temperature and humidity. The minimum and maximum values are updated automatically when a new minimum or maximum is recorded, or until manually reset. GB P. 12 P. 13 GB a. From the normal display mode, press and release the "OUT/+" key once to view the outdoor maximum temperature and humidity ("MAX" will be displayed above the outdoor temperature and humidity). Press and release the "OUT/+" key again to view the outdoor minimum temperature and humidity. Press and release the "OUT/+" key again to return to the normal mode (timeout of viewing minimum/maximum values will occur if no keys are pressed for fifteen seconds). Note: To reset the outdoor minimum and maximum temperature and humidity, first display the values you wish to reset (minimum or maximum). Next press and hold the "SET" key for at least three seconds. You will see then that the values will reset to the current temperature and humidity and corresponding time. Multiple Remote Temperature Sensors The WS-9032U is able to receive signals from 3 different remote sensors. These extra remote sensors can be purchased through the same dealer as this unit. [. . . ] Dimensions (H x W x D) Indoor weather station 8. 93 x 4. 62 x 1. 22 inches (227 x 117. 4 x 31. 2 mm) Remote thermo/hygro sensor 4. 29 x 1. 56 x 0. 78 inches (110 x 40 x 20 mm) WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. GB P. 20 P. 21 GB WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. [. . . ]