User manual LA CROSSE TECHNOLOGY WS-7215TWC-IT

[. . . ] WS-7215U-IT Wireless 915 MHz Radio-controlled Temperature Station Instruction Manual TABLE OF CONTENTS Topic Inventory of Contents/Additional Equipment About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery installation Program Mode Program Sequence and Default Settings Function Keys Setting the LCD Contrast Setting the Time Zone Daylight Saving Time Setting Radio-controlled Time Setting 12/24-hour Time Setting Setting the Time Setting the Year, Day and Month Setting the Snooze Setting the Temperature Format Setting the forecast sensitivity Features Indoor Temperature and Humidity Outdoor Temperatures Minimum & Maximum Records (Indoor, Outdoor, & Resetting) Additional Remote Control Sending Units (Set-Up, Viewing, & Operation) Mounting Troubleshooting Maintenance & Care Specifications Warranty Information Page 3 3 4 5 6 6 7 7-8 8 9 9 10-11 11 12 12 13 13 14-15 15-16 17-18 19-20 20 21 22-23 2 This product offers: INSTANT TRANSMISSION is the stateof-the-art new wireless transmission technology, exclusively designed and developed by LA CROSSE TECHNOLOGY. INSTANT TRANSMISSION offers you an immediate update (every 4 seconds!) of all your outdoor data measured from the sensors: follow your climatic variations in real-time! INVENTORY OF CONTENTS 1. Instruction manual and warranty card. Figure 1 Figure 2 Time LCD Date LCD Indoor LCD Outdoor LCD Mounting TX29U-IT remote Bracket temperature sensor ADDITIONAL EQUIPMENT (not included) 1. Two fresh AA 1. 5V batteries for the Wireless Temperature Station. 3 2. [. . . ] Press the OUT button again (once while "MIN" is still displayed, twice otherwise). "MAX" appears above the outdoor temperature and the LCD will flash, indicating that the maximum temperature and the time and date of occurrence are displayed. 3. While "MAX" is still displayed press the OUT button again to return to the current data display. Or you can wait 30 seconds, during either the minimum or the maximum readings, and the unit will automatically return to current data readings. C. All the Indoor records (minimum and maximum) will be reset after the IN button is pressed and held for 5 seconds. All the Outdoor records (minimum and maximum) will be reset after the OUT button is pressed and held for 5 seconds. IV. ADDING REMOTE TEMPERATURE SENSORS (OPTIONAL) The WS-7215U-IT is able to receive signals from 2 additional temperature sensors. The following are instructions for the set-up of temperature sensor units with the WS-7215-IT. These extra sensors can be purchased through the same dealer as this unit. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds. During these 60 seconds, press any button 20 times to discharge any excess power. Within 30 seconds of powering up the first sensor, insert the batteries to the Temperature Station. Once the batteries are in place, all segments of the LCD will light up briefly. Following the indoor temperature and 16 humidity, and the time as 12:00 will be displayed. If they are not shown in LCD after 60 seconds, remove the batteries and wait for at least 60 seconds before reinserting them. The outdoor temperature from the first sensor (channel 1) should then be displayed on the Wireless Temperature Station. If this does not happen and the signal reception icon is not shown, after 2 minutes, the batteries will need to be removed from both units and reset from step 1. Insert the batteries to the second sensor as soon as the outdoor temperature readings from the first sensor are displayed on the Wireless Temperature Station. NOTE: You must insert the batteries into the second sensor within 10 seconds of reception of the first sensor. The outdoor temperature from the second sensor and the "channel 2" icon should then be displayed on the Wireless Temperature Station. If this does not happen after 2 minute, the batteries will need to be removed from all the units and reset from step 1. Insert the batteries to the third sensor as soon as the "channel 2" icon and outdoor data are displayed on the Wireless Temperature Station. Then within 2 minutes, the channel 3 outdoor data from the third sensor will be displayed and the channel icon will shift back to "1" once the third sensor is successfully received. [. . . ] La Crosse 22 Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. [. . . ]