User manual KARCHER SE 3001

[. . . ] These are entirely harmless and are not associated with the mains supply. To minimise any effect from this, do not put your hand or insert any object into the clear bin unless you have first emptied and rinsed out the clear bin with water. Ensure that hands, feet and fingers, particularly those of small children, are kept away from the cleaner and especially from the brush bar. Please note that the brush bar continues to turn while the hose is in use ­ ensure that the cable is clear of the machine during this operation and that the cleaner is not placed near anything which may come into contact with the brushbar. [. . . ] Do not use the cleaner directly facing gas fires, boilers or open fires, whether lit or unlit. Exhaust air discharged at the front of the cleaner may extinguish a gas fire or pilot light or disturb ashes in an open fire. Always avoid directing the cleaner towards naked flames. 2. 8. 3. 9. 4. 5. 10. Do not use the cleaner to pick up flammable or combustible substances or hot ashes or burning objects of any kind. Ensure this is completely dry before using the cleaner again. 6. KARCHER CUSTOMER CARE Helpline 01666 827272 T ET B U RY HILL Facsimile 01666 827298 Contact for all service assistance MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P 00753-01 00746-01 21/11/97 REV 1 1. Getting started Assemble the machine as follows: P L E A S E R E A D A L L I N S T R U C T I O N S C A R E F U L LY BEFORE USING YOUR KARCHER VACUUM CLEANER. Wand & hose assembly Push yellow hose cuff firmly over wand end with twisting motion. Accessory tool location All tools are stored neatly on the tool storage posts. 1 Tool adaptor 1 Guide wand into hose, keeping it straight. 2 Locate wand handle into socket from above. 3 Push home until it `clicks' into place. Ensure hose does not kink when replacing wand . . . to release cable. 4 Insert tool on to end of wand as shown. 5 For cleaning awkward places remove wand and insert tool adaptor into end of hose. Attach tool as required. Cleaner head adjustment Hold the cleaner head down with foot and tilt machine back. 5 Tool adaptor On/Off switch Cleaner head adjusts automatically to correct height. 2. How to use Clear bin capacity Do not fill above this line. WARNING! For your own safety please remember to unplug the machine when not in use and before carrying out maintenance. Carrying handle Ensure clear bin is firmly in place before lifting. Clear bin removal & emptying 1 Press yellow bin catch to release bin. 2 Remove clear bin and cyclone top from machine by lifting up until it releases. 3 Remove clear bin from cyclone top and wrap a plastic bag around the rim of the clear bin. 4 Invert clear bin and wait at least 10 seconds before releasing. 5 Wipe shroud holes free of all dust and debris. 6 Replace clear bin and cyclone top ensuring that they `click' into upright position. Filter changing 1 Lift out pre-filter. Unhinge filter cage and replace old S-level submicro filter at least every three months. Optional clear bin cleaning Remove clear bin from machine to wash in water if desired. After washing ensure that the yellow bin inner is in place (See step 7 of `Blockage procedure' in your instructions). Check cone seal is in place: failure to do so could result in clogging of the pre-filter and damage to the motor. The lip of the cone seal should sit over the rim of the yellow bin inner. 6 5 5 Check for any blockages in hose and remove. Cone seal 6 When returning hose, ensure the yellow button `clicks' into place. (A tool may be required to ease re-assembly). KARCHER CUSTOMER CARE If you are still unable to get `suction', call T ET B U RY HILL Dyson Customer Care on 01666 827272. MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P Important Check both electrostatic filters whenever the bin is emptied and replace at least every 33 months. Please note that if the filters are not checked regularly and changed as required, the motor may overheat, which will cause the thermal cut-out to operate. NOTE: Vacuuming builder's dust and some carpet fresheners may cause the filters to require changing more frequently. Replacement filters are available from your local retailer or direct from Dyson. Call or fax the Helpline for orders. S-Level S IMPORTANT: Use only genuine Dyson filters, which have been tested and approved for this cleaner. NOTE Your Dyson has a built-in thermal cut-out to protect it in the event of a restriction to the airflow and may suddenly stop working temporarily if you do not change the filters at the stated time, or if blockages are not cleared immediately. If the vacuum cleaner suddenly stops working (ie. the motor makes no sound when switched on) then please check your cleaner for blockages as detailed in this operating manual. Having established that there are no blockages and that the filters have been replaced within the stated time, leave your vacuum cleaner unplugged for 60 minutes and then try using it again. If the vacuum cleaner still does not work, please call Dyson Customer Care (Tel: 01666 827272). IMPORTANT A LWAY S U N P L U G T H E VAC U U M C L E A N E R F R O M T H E WA L L S O C K E T B E F O R E I N S P E C T I N G I T NOTE Check that your supply corresponds to that shown on the rating plate. The appliance must only be used as rated, it should be fitted with an ASTA approved fuse to BS1362. European conformity information A sample of this product has been tested and found to be in conformity with the following European Directives: 73/23/EEC Low voltage (safety) Directive, 93/68/EEC CE Marketing Directive and 89/336/EEC EMC Directive. [. . . ] European conformity information A sample of this product has been tested and found to be in conformity with the following European Directives: 73/23/EEC Low voltage (safety) Directive, 93/68/EEC CE Marketing Directive and 89/336/EEC EMC Directive. For your convenience this appliance is supplied with a plug which is fitted with a 13amp fuse of the appropriate rating. Never put the plug into the socket outlet without the fuse cover fitted. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed/safely disposed of. [. . . ]