User manual KARCHER SE 2001

[. . . ] working temporarily if you do not change the filters at the If the vacuum cleaner suddenly stops working (ie. the motor makes no sound stated time, or if blockages are not cleared immediately. when switched on) then please check your SE 2001 for blockages as detailed If the vacuum cleaner suddenly stopsalso to check the fuse in the plug). the motor makes no sound when switched on) then please check your cleaner for blockages as Important safety instructions ­ please read before use WHEN USING THE KARCHER DCO2 VACUUM CLEANER PLEASE ADHERE TO THESE SIMPLE PRECAUTIONS. B Y D O I N G S O Y O U W I L L R E D U C E T H E R I S K O F F I R E , E L E C T R I C A L S H O C K O R I N J U R Y. 1. [. . . ] Do not leave your Dyson cleaner with the plug connected to a mains outlet ­ unplug when not in use. Turn the cleaner off with the switch button before removing from the mains outlet. Always remove the plug from a mains outlet before carrying out any maintenance. Do not carry out any maintenance work on the cleaner other than that outlined in this manual, especially where electrical components are concerned. Do not use without the clear bin assembly fitted correctly and both filters in place. Do not fit anything other than Dyson spare parts (available on the Helpline on 01666 827272). Do not continue to use the cleaner if any part appears to be faulty, missing or damaged. Do not put any part of the body, clothes or any object near or into the openings or moving parts of the machine. Do not use the machine with any of the openings blocked with any object that may restrict the airflow. Do not pull on the supply cord, run over it or pull it around sharp edges or near/over hot surfaces. These are entirely harmless and are not associated with the mains supply. To minimise any effect from this, do not put your hand or insert any object into the clear bin unless you have first emptied and rinsed out the clear bin with water. 4. 5. 6. 7. KARCHER CUSTOMER CARE KARCHER CUSTOMER CARE Helpline 01666 827272 T ET B U RY HILL Helpline 01666 827272 T ET B U RY HILL Facsimile 01666 827298 Contact for all service assistance MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P Facsimile 01666 827298 Contact for all service assistance MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P 03-28-208 05-28-055 14/02/97 REV 1 1 Changing filters Your DCO2 is fitted with two high area H-level electrostatic cartridge filters. Alternatively a standard S-level filter may be purchased. m ax m ax 2 1 Insert top filter ensuring that it fits snugly against the black rubber seal on the machine. Fitting instructions for the standard S-level filters are printed on the filter itself. H H-Level S-Level S Clear bin full mark Note: Do not fill above this line. 2 H-level OR 1 S-level 2 Automatic suction control trigger Hold the yellow trigger down to reduce suction for upholstery and curtains. 2. Clear bin removal IMPORTANT Use only genuine Dyson filters. To maintain reduced suction, press the trigger down hard until it clicks. To unlock and resume full suction, press down the opposite end of the trigger. Sits securely on the stairs However, always work above the machine on stairs for your own safety. Telescopic wand click 3 Press yellow button and slide wand down to adjust length. Blockage procedure Please note: Any `Blockage only' repairs will incur a charge of £35. 00 *. Check filters, replace if older than 3 months, or if filters are heavily coated with dust. 1 To empty clear bin, pull back release catch under carrying handle and raise top of machine. 1 *Price correct at time of printing. 2 Lift clear bin out of machine. 1 1. Check entry swivel by pressing yellow buttons & pulling out hose. Clear any debris. 3 Remove cyclone top (lid). 1 The plug is situated underneath the tool cover on the right hand side. 1. Hose & wand assembly Assemble hose and wand by fitting 3 together at joints 1 , , and . [. . . ] Hose & wand assembly Assemble hose and wand by fitting 3 together at joints 1 , , and . Check wand handle swivel 2 by pressing yellow buttons and pulling hose from wand. Clear any debris. On/off switch Press left switch. Tool storage Press yellow release catch to open the tool storage cover and insert required tool into end of wand or wand handle. Please note that tools may feel warm when machine has been running; this is perfectly normal. Wand handle Wand Self adjusting Floor tool Fit floor tool by pushing firmly into end of wand. 3. [. . . ]