User manual KARCHER HDS 698 CSX

[. . . ] Caution Possible hazardous situation that could lead to mild injury to persons or damage to property. 20 Symbols on the machine High-pressure jets can be dangerous if improperly used. The jet may not be directed at persons, animals, live electrical equipment or at the appliance itself. general notes on safety – – – – – Environmental protection The packaging material can be recycled. [. . . ] The outer scale is applicable while using undiluted detergents (100% CHEM). The main switch of the vacuum cleaner is to be switched off or the Cekon plug must be unplugged while carrying out any repairs or maintenance jobs. Maintenance schedule Performance Check whether the hand-spray gun closes tightly without any leaks. Check high pres- Outlets, hoses towards working Check hoses to see if there are damages. Check the con- Electrical connection with plug/ Check the connecting line with mains plug for necting line with socket damages. If the power cord is damaged, please mains plug arrange immediately for the exchange by an authorized customer service or a skilled electrician. Weekly or after 40 Check oil level Oil tank at the pump If the oil is milky, it needs to be replaced. Operating hours Check oil level Oil tank at the pump Check oil level of the pump. Sieve monthly or after Check pump High-pressure pump Check the pump for leaks. If the leakage is more 200 operating than 3 drops per minute, call Customer Service. Hours Check for inter- Entire plant Operate the machine using the spray pipe withnal deposits out the high pressure nozzle. Fuse in the control circuit (F3) has Install a new fuse; if it burns out again, then burnt off. + Indicator lamp for engine Thermal sensor (WS) in the engine Rectify cause for over-loading. Over-heating (G) is glowing or the over-current protection switch (F1) has got activated. Burner does not ignite or the Thermostat (B) has been set at a Set the thermostat to a higher level. The maximum temperature limiter Let the boiler cool down and restart the appliin the water outlet (> 110 °C) has ance. Add 5 litre water via the measuring nozzle for Boiler floor is too hot. Mum temperature limiter in the boiler floor (> 80 °C) has got triggered. Automatic gas firing system is Press the unlocking key for the gas relay (I). Blower or speed control plate is de- Check blower and speed control plate. Of whom Electrician Operator Customer Service Customer Service Customer Service Customer Service Operator Operator Operator Operator Operator Operator Customer Service Operator Operator Operator Operator Customer Service Customer Service * Note Press unlocking key for exhaust gas thermostat (J) to unlock the flame monitoring mechanism. Remedy of whom Open the hand-spray gun until the plant has Operator cooled down. [. . . ] The operations stand-by time is set in the factory to a minimum time of 2 minutes and can be increased to a maximum time of 8 minutes. EN - 17 39 Installation material 1 2 3 5 6 7 8 9 10 12 13 11b 11a 25 21 22 23 A 15 11b 11d 11a B 11c 24 4 20 19a 19 18 17 16 14 Figure 3 Item: 1 2 3 4 5 6 7 8 9 10 11a 11b 11c 11d Installation material Threaded elbow joint Set of connecting parts, exhaust Set of boiler connecting parts, exhaust Set of siphon parts Thermal insulation Main switch Set of pipes, galvanised steel Set of pipes, stainless steel Remote control set Set of parts for emergency-stop switch T-screws Connection neck, brass Connection neck, stainless steel Shut-off valve NW 8, galvanised steel Shut-off valve NW 8, stainless steel Fixed part for quick coupling Loose part for quick coupling Order No. ) Set of parts for wall console Set of parts for floor frame High pressure hose Order No. 389-028 40 EN - 18 EC Declaration of Conformity We hereby declare that the machine described below complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us. [. . . ]