User manual HITACHI POWER TOOLS CB100F ELECTRIC TOOL PARTS LIST

[. . . ] 4 Accessories and Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Know Your Band Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Place the trunnion support bracket (3) on the saw body, as shown, aligning the mounting holes. Place the washers on the hex head bolts, and insert into the threaded holes, through the bracket and saw body. Thread a nut (4) onto the table stop bolt (5) and screw bolts into the rear tab (6) on the trunnion support bracket. Place a lock knob (16) on each scale knob bolt adjust the table by aligning the zero scale mark to the scale pointer (17), and tighten the knob. Place the table aligning pin (18) in the hole at the front of the table, and tighten. Fig. D 1 2 6 3 5 4 17 16 -- 12 -- INSTALLING AND REMOVING THE BLADE(Fig. G) WARNING!To avoid injury from accidental starting, always turn the switch OFF and remove the plus from the power source before moving, replacing, or adjusting the blade. Loosen the blade tension by turning the blade tension knob (1) counterclockwise. Remove the table insert (2) and the table aligning pin (3) from the table. Unfasten the screw (13) at the right of extension tube and remove the extension table from the table. Loosen the two Phillips screws (5) and remove the upper blade guard (6). When the adjustment is accurate at 90°, align the pointer (7) to 0° the scale (8) Fig. K 1 6 5 ADJUSTMENT INSTRUCTIONS WARNING To avoid injury, turn the switch OFF and unplug the band saw from the power source before making any adjustments. Tilt the table to the desired angle on the scale (3) underneath the table. L) 5. WARNING To avoid injury, turn the switch OFF and disconnect the saw from the power source before making any adjustments. The gauge (1) on the bracket (2) at the rear of the upper wheel housing indicates the proper tension for the various blade widths. Set the blade tension gauge to correspond with the width of the blade in use. Turn the blade tension knob (3) clockwise, raising the upper wheel to tighten the blade. Turn the knob counterclockwise to lower the upper wheel, loosening the blade. As you become familiar with the saw, you may want to change the tension settings. NOTE: Changes in blade width and type of material being cut will have an effect on the blade tension. 3 6. If the blade moves toward the front of the wheel, turn the tracking knob (5) on the rear of the band saw clockwise. [. . . ] LUBRICATION All of the bearings are packed with grease at the factory. CAUTION: Never put lubricants on the blade while it is spinning. -- 20 -- TROUBLESHOOTING GUIDE WARNING To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source before making any adjustments. All electrical or mechanical repairs should be done only by qualified service technicians. Contact Hitachi Authorized Service Center. GENERAL PROBLEM Blade does not run in the center of the upper wheel. [. . . ]