Detailed instructions for use are in the User's Guide.
[. . . ] · The following table describes the icons used in this Operation Manual.
Icon Tips and Hints for easier operation Meaning
DVD
VIDEO CD
Functions for DVD
Functions for VIDEO CD
CD
Functions for Audio CD
GENERAL INFORMATION
CONNECTION AND INITIAL SETTING
VCR, DVD SETUP
WATCHING THE VCR, DVD
OTHER INFORMATION
Important!
Be sure to read this Operation Manual carefully before using the Product for the first time, and keep it on hand for future reference when you experience operational problems.
SAFETY INFORMATION
GENERAL INFORMATION
<Only for DV-NC70W/70> Note: This Product can be used only where the power supply is AC 110V-240V, 50/60Hz. <Only for WCW NITRO STING091> Note: This Product can be used only where the power supply is AC 240V, 50Hz. It cannot be used elsewhere.
· This Product is classified as a CLASS 1 LASER product. · The CLASS 1 LASER PRODUCT label is located on the rear cover. [. . . ] · If your TV does not have a V-HOLD control, the picture may roll and be unwatchable. However, if you use a TV with a V-HOLD control, you can stop the rolling by adjusting the V-HOLD control and watch the picture. · Horizontal noise bars may appear on the screen during special effect playback (video search, still, slow, frame advance, and double speed playback), possibly accompanied by discolouring. · Although NTSC tapes can be played back into a PAL TV, those tapes cannot be dubbed by a PAL system VCR connected to the AUDIO OUT and VIDEO OUT terminals of this product. · Set the Colour mode to AUTO or NTSC, and set the NTSC mode to PAL TV.
Full Auto Playback
(This function only works when AUTO RENTAL mode on the MODE selection screen is set to "OFF". ) Full Auto Playback lets you enjoy playback with ease. When you insert a cassette with the erasure protection tab removed, your Product automatically turns on the power and plays back the tape. When the tape reaches its end, the Product automatically rewinds the tape, ejects it and turns off the power. If a DVD is being played back, the power will not turn off.
· If the erasure protection hole is covered, press ûPLAY after the power turns on automatically.
Auto Head Cleaning System
When the tape is inserted or ejected, this system automatically cleans the drum and heads with a special roller before recording or playback begins, protecting the heads and drum from dirt and preserving beautiful picture quality.
Auto Tracking Control System
This function automatically adjusts the tracking to match the recorded tape. Auto tracking engages in the following cases: · When you insert the cassette and begin playback. · When the Product has been playing back an unrecorded section of tape, Poor Tracking and then reaches a recorded tape segment. When auto tracking engages, "|" on the TV screen flashes for a few seconds. A blue screen will appear if audio-only Hi-Fi tapes are played back.
TIMER OPERATE ON/OFF
DV- NC70 DV- NC70X
EJECT
Audio Output Mode
DISPLAY
VCR/DVD VCR MENU ON SCREEN SELECTOR DVD SETUP
OPEN/ CLOSE
The audio output mode is controlled by AUDIO OUTPUT on the Remote. The Product is normally set to the Hi-Fi mode, with and displayed on the VCR Front Panel display, and normal stereo sound output. Select , and only the Hi-Fi Left channel audio is heard from both the Right and Left speakers. Select , and only the Hi-Fi Right channel audio is heard from both the Right and Left speakers. If you select the mono linear track, and will disappear.
· Should the Hi-Fi output level be poor, the Product will automatically select the mono linear track output. · When playing back tapes which have only Hi-Fi sound recorded: If Hi-Fi sound is not reproduced, or if there is some noise in the audio, press CH ' / " until the sound improves.
FUNCTION PROG/ CONTROL REPEAT
ANGLE
TITLE
CLEAR RETURN
DVD MENU
SET ENTER
ZERO BACK
SKIP SEARCH
AM/PM
INPUT SELECT VCR DVD
/
REV PLAY REC STOP
PAUSE/STILL
FWD
Adjusting Hi-Fi Audio Tracking
(To adjust the Hi-Fi tracking manually when playing back a poorly recorded Hi-Fi tape. ) · Normally you can simultaneously press and hold both CH ' / " to obtain the optimal Hi-Fi audio tracking. · If Hi-Fi audio is unstable (frequent dropouts, etc. ) with a rental video, a tape recorded on another VCR, restore normal tracking while playing back the tape as described below:
TAPE SPEED
DPSS SKIP AUDIO OUTPUT VCR DVD
SLOW
CH
VCR/DVD COMBINATION
1 2 3 4 5
Press ON SCREEN on the Remote and select the Full Display mode. Press CH ' / " repeatedly at equal, short intervals until the and indicators disappear from the On Screen Display (OSD). Press CH ' / " in the same manner while counting button operations until the L and R indicators reappear and then disappear again. Press CH ' / " again for half the number of times counted in step 4 above to obtain optimal track.
57
GB
Sharp Super Picture
This function creates clearer picture quality only during playback.
1 2
Press VCR MENU to display the menu screen. Select "MODE" with ' / " and then press SET to confirm.
MENU G-CODE TIMER MODE CHANNEL PRESET CLOCK LANGUAGE :SELECT SET:ENTER
TIMER OPERATE ON/OFF
DV- NC70W DV- NC70 DV- NC70X
G-CODE PROG
MENU:EXIT
EJECT
DISPLAY
VCR/DVD VCR MENU ON SCREEN SELECTOR DVD SETUP
3
Select "S. PICTURE" with ' / ". [. . . ] The original high picture quality of SVHS (horizontal resolution of 400 lines) cannot be played. When noise appears on an image during tape playback, you can adjust the image quality to a suitable level so as to reduce the noise.
s DVD
Angle
Recorded onto some DVD discs are scenes which have been simultaneously shot from a number of different angles (the same scene is shot from the front, from the left side, from the right side, etc, ). With such discs, you can select the angle on Function Control Screen to view the scene from different angles. A title is subdivided into many sections, each of which is numbered, and specific parts of video presentations can be searched quickly using these numbers. [. . . ]