User manual HARMAN KARDON HKTS 7 [HKTS 7/230]

[. . . ] It also includes stereo speaker-level inputs and outputs for connection to older receivers and processors that do not have a line-level subwoofer output. Other conveniences include a level control, high-cut (lowpass) filter switch and phase switch for fine-tuning bass response to suit your listening environment and taste, and an efficient switching system that senses the presence of an audio signal and automatically switches the unit from Standby mode to Active mode. Shelf stands and wall-mount brackets are included for the satellite speakers, and optional HTFS 2 floor stands are available separately from your Harman Kardon dealer. With state-of-the-art features and time-honored circuit designs, the HKTS 7 is a perfect complement to a Harman Kardon receiver or any home theater system. [. . . ] However, the best reproduction of bass will be heard when the subwoofer is placed in a corner along the same wall as the front speakers. The customer is responsible for proper selection and use of mounting hardware, available through hardware stores, to properly and safely wall-mount the speakers. Referring to the speaker connection instructions on pages 8 through 11, thread the appropriate speaker cable through the opening in the bottom of the attachment plate, and then through the back of the bracket as shown in the diagram. Wall Bracket Insert the supplied bracket bolt up through the bottom of the bracket and terminal cover, and screw it into the threaded insert on the underside of the speaker. The bolt should be snug, but not so tight as to prevent the bracket from pivoting. MOUNTING OPTIONS 7 Speaker Connections Speaker-Level Connection Guide IMPORTANT NOTE: Before making speaker connections, be certain that your receiver or audio power amplifier is turned off and preferably unplugged from its AC power source. The SUB-TS7 subwoofer should not be connected to an AC power source until all speaker wire connections have been made. Speakers and electronics terminals have corresponding (+) and (­) terminals. Most manufacturers of speakers and electronics, including Harman Kardon, use red to denote the (+) terminal and black for the (­) terminal. With the advent of multichannel surround-sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. To connect the supplied speaker wires to the satellite and center speaker terminals located on the bottom of each speaker, press the red or black tab, insert the bare end of the wire into the hole, and release the tab. For the best performance, Harman Kardon recommends that the subwoofer be connected using either the Line-Level Subwoofer (SUB) Input 4 or the Line-Level Full-Range Inputs 5. However, if the application requires the use of the speaker-level connections for the subwoofer, unscrew the binding-post collar until the pass-through hole in the center post is visible under the collar. Insert the bare end of the wire through this hole; then screw the collar down until the connection is tight. The hole in the center of each collar is intended for use with banana-type connectors. Newer Harman Kardon receivers conform to the CEA standard and therefore use a color other than red or black for the (+) terminal to indicate some speaker positions: e. g. , surround left. Although the HKTS 7 system has red and black collars on the individual speaker terminals to denote the positive and negative connections, your system includes a colored band on the positive lead at both ends of every speaker cable and a matching colored sticker for each of the four satellite speakers, conforming to the key on page 7. The center speaker has a green (+) terminal, and the subwoofer has a purple SUB input jack. This system is intended to help you ensure that the speaker in each location is connected to the correct terminals on your receiver or amplifier. The (+) lead of the speaker wire is indicated with a stripe and has the colored band corresponding to the speaker's position. It is important to connect all speakers identically: (+) on the speaker to (+) on the amplifier and (­) on the speaker to (­) on the amplifier. Wiring "out of phase" results in thin sound, weak bass and a poor stereo image. 8 SPEAKER CONNECTIONS Speaker Connections Dolby Digital or DTS® (or Other Digital Surround Mode) Connection Use this installation method for Dolby Digital, DTS® or other digital surround processors: Use the line-level input jack marked "SUB" for the Low-Frequency Effects channel. Connect this jack to the LFE output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround-sound processor for "Subwoofer On. " The front left, front right, center and rear speakers should all be set to "Small. " Front Left ­ + Center ­ + Front Right ­ + SUB-TS7 Subwoofer LINE LEVEL IN SUB R L Front Left SUB/LFE Out Surround Left Center Front Right Surround Right Surround Left ­ + Receiver Surround Right ­ + SPEAKER CONNECTIONS 9 Speaker Connections Dolby Pro Logic (Non-Digital) ­ Line Level Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS® or other digital processing), where the receiver/processor is equipped with a subwoofer output, or a volume-controlled preamp (line-) level output: Use RCA-type patch cords to connect the linelevel subwoofer output on your receiver or to amplifier either the left or right line-level input on the subwoofer. [. . . ] · In Dolby Digital or DTS® modes, make sure your receiver/processor is configured so that the subwoofer and LFE output are enabled. · Check all wires and connections between receiver/ amplifier and speakers. · Review proper operation of your receiver/amplifier and its surround-sound features. · Make sure the movie or TV show you are watching is recorded in a surround-sound mode. [. . . ]