User manual HARMAN KARDON HD7325

[. . . ] a ­ (number in an oval) indicates a button or indicator on the remote. ¡ ­ (number in a circle) indicates a rear panel connection. 2 TABLE OF CONTENS Introduction Thank you for choosing Harman Kardon HD7325 CD player. The HD7325 is an exceptionally well-engineered product that offers high performance and ease of use. Along with conventional CD audio discs, the HD7325 is also compatible with MP3 data from CDs and most recordable CD formats. [. . . ] If the HD7325 is installed behind a cabinet or other obstruction that may block the path between the front-panel Remote Sensor and the location of the remote, an optional external IR sensor may be used. Connect the sensor to the Remote IR-In Jack £ on the rear panel. This jack may also be connected to the IROutput jack of another compatible Harman Kardon component or a compatible IR-systemremote product. You may also use the IR Sensor in the HD7325 to send commands to other compatible remote controlled products. Connect the Remote IROut jack ¢ to the input of the other product or system. Connect the power to a nonswitched AC wall outlet or to the accessory outlet on the rear of another audio device in your system and you are ready to go!NOTE: When using the accessory outlet on another product to power the HD7325 make certain that it has the compatibility to power a device that draws at least 14 watts of current in addition to being able to handle the requirements of the other devices that may be plugged into the accessory outlets. If you use a "switched" outlet, it is important to remember that the host product must be turned on in order for the HD7325 to operate. INSTALLATION 9 Operation Loading and Unloading Discs To load a disc, first turn the unit on (if not so already) by pressing the Power Switch 2 on the front panel or the Power On button 1 on the remote, then press the Open/Close button 3 F taking care to make certain that the space in front of the drawer is not obstructed. When the unit is turned off (to Standby), pressing the Play button 4 9 on the front or on the remote will automatically turn on the CD player and start playback. When an 8cm disc is played, it should be carefully centered within the smaller ridges inside the cassette drawer. Disc Handling Notes When loading or unloading discs, it is best to hold them by the edges. As a disc plays, the track numbers will change, and the time will reset to at the start of each new track. Note that a Pause indication ± will appear in the display to remind you that the disc is paused. Press either the Play button 4 9 or the Pause button 5 9 to resume normal play. When the Stop button is pressed the display again will show the total number of tracks and total running time of the disc. To prevent dirt and dust from entering the unit, do not leave the disc tray open. To place the unit in a Standby mode, press the Power Switch 2 on the front panel or the Power Off button 0 on the remote. The display will show a STANDBY message for a moment and the Status Mode Indicator will glow orange, indicating that the unit is off, but ready to accept a Power On command from the remote. If the disc drawer is open, it will automatically close when the unit is placed in the Standby mode. This ensures that the unit will not be harmed from dust, dirt or inadvertent damage to the drawer mechanism. Note that the unit is not removed from AC main power when it is in the Standby mode but its power consumption is reduced to a low value. To remove the AC power completely from the unit its Power Cord must be plugged into a switch controlled AC outlet that is turned off. [. . . ] Repeat this procedure for each program step until you have completed the desired programming. Press the Stop button 6 A once to complete a program sequence, or press Play 4 9 to begin immediate play of a program sequence. If the maximum of 99 program steps is reached, the program-step indication at the right side of the Information Display will go out, and the disc and track that have been programmed as the first program step will be shown. Editing a Program A program can be edited even after it was completed by pressing the Stop button 6 A once: Each time you press the Program button 3 the track number and program step number will be displayed in the programmed order, but with steady tracks numbers (not blinking) in contrast to the programming mode. As soon as the track number starts blinking (this will take 1 second), the appropriate program step number shown at the left side is not programmed yet; now you can change the track number with the Skip buttons 7 8 7 or the Numeric buttons 2 as described above and add it to the program list by pressing the Program button 3. [. . . ]