User manual HARMAN KARDON DRIVE + PLAY 2 [HK-DP2EU] QUICK START GUIDE FOR DRIVE + PLAY 2 (ENGLISH)

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Important! Connecting the iPod Player Always hold the Drive + PlayTM 2 system's dock connector for the iPod player by its sides and gently insert (or remove) the dock connector. Never use excessive force to insert or remove the connector, or damage to your iPod player may occur. [. . . ] Tighten screw again to secure base. ! 4 The installation of this device between the driver and the windshield or otherwise in any manner that obstructs the driver's clear view of the road or traffic conditions is dangerous and may be prohibited by law. Do not install this device in any manner that impairs the safe operation of the vehicle. The display should be positioned to eliminate glare and reflections, and should be as close as possible to the driver's normal line of sight, as long as such positioning does not otherwise obstruct the driver's view or impair the safe operation of the vehicle. Do not install this device on any air bag panels or in the deployment field of any air bags. For safety reasons, do not attempt to disable any safety function incorporated in this device. Any alteration of this device may cause serious injury and shall void the warranty. Quick-Start Guide Installing the Display Mounting With Screws 1 Align Al mounting plate to location and attach with lo three th screws. Place display base onto mounting plate and rotate into desired position. 1 2 3 4 Mounting With Adhesive Pad 1 In Insert mounting plate in into display base and tig tighten hex set screw. Stick adhesive pad to ba base first, then clean su surface of mounting loc location with supplied alc alcohol pad. Peel adhesive pad and press display firmly into desired location. Base 2 2 Base Hex Screw 3 Ti Tighten the hex screw to lock th the display base onto the m mounting plate. Hex Screw 3 4 Mounting Plate After Mounting Mounting Plate Plug cable e into display. ay. Adhesive Pad Quick-Start Guide 5 ENGLISH Installing the Wireless Control Knob 2 1 1 2 3 4 Install Control all Cont Knob Battery Use a coin to remove the bottom cover. Select Control Knob Mounting Location CR2032/DL2032 Toward front of car 3 M Mount Control Knob Base Orient the base so that the arrow is facing the front of the car. You can either screw the base to the mounting location or use the supplied adhesive pad. If you use the adhesive pad, you must FIRST CLEAN the surface with the supplied alcohol cleaning pad. 4 UP Attach Control ch Cont Knob to Base UP Push the knob down onto the base, and turn clockwise to lock it into place. The knob can be removed by turning the bottom counterclockwise. 6 Quick-Start Guide Connections to the Cigarette Lighter Hub 1 1 2 3 Power Indica r Indicator Direct Cigarette Lighter Plug-In Plug into vehicle. harman net t Expansion Port t Options 2 Cigarette Lighter Extension Cable Display iPod Player Audio Output Options 1. If using the built-in wireless FM transmitter, leave the audio output jack empty. YELLOW = Constant source of +12V RED = Switched source of +12V (ACC) BLACK = Ground 2. To wire directly to your vehicle's antenna, plug the supplied FM transmitter adapter into the audio output jack. To wire into an AUX input, connect the included audio cable's 3. 5mm plug to the audio output jack and then into your vehicle's AUX input. Audio Output 3 Detach lighter stalk. Stalk fits tightly. Some force is required to separate. Hard-Wired Installation Q kS Quick-Start G d Guide 7 ENGLISH Wired FM Transmitter Adapter Connections Connect in the line between vehicle antenna and radio. 1 2 3 1 Plug the adapter into the back of radio or FM tuner location. 2 Connect FM transmitter adapter to Drive + Play 2 system. 3 Plug the vehicle's antenna into FM transmitter adapter. If your car's audio system does not provide an auxiliary input and there is no third-party adapter available, use the Drive + Play 2 system's wired FM antenna adapter for the best audio performance. See page 12. 8 Quick-Start Guide Using the Control Knob Rotate ring to move the highlight bar on the screen Show previous menu (press and hold to show special features) Previous Press and hold to REWIND Press once to toggle PLAY/PAUSE Press and hold for 2 seconds to turn ON/OFF Next Press and hold to FFWD Press to select the highlighted menu item Note: If the Drive + Play 2 system is turned off using the bottom button, it must be turned back on that way!If the control knob is unresponsive, try pressing the top, center and right buttons simultaneously for 2 seconds, then turn the outer ring until the highlight bar moves. If the control knob is still unresponsive, try a fresh CR2032-type battery. Quick-Start Guide 9 ENGLISH iPod Player Functions 1 2 3 iPod Connection Confirmation nfirmation rmation at o on When your iPod player is successfully connected, the iPod icon appears in the top-right corner of the display. [. . . ] Remember, you may try several frequencies for the best result. 1 Enable the FM transmitter and select FM frequency preset. System Settings FM Transmitter Enable Preset 1 : 88. 1 Preset 2 : 88. 7 Preset 3 : 107. 9 Add Preset Yes Settings Once you have selected an FM preset, tune your FM radio to that same station. If that frequency is not playing music clearly, select another preset by locating a frequency on your radio that is only static and save that as a preset. This will offer the clearest path for the Drive + Play 2 system's audio playback. Line-Output Audio Connections To use the Line-Out audio connection, the FM transmitter must first be disabled using the steps shown. Following that, you will need to connect into your head unit's AUX input. [. . . ]