User manual HARMAN KARDON AVR 4000

[. . . ] AVR 4000 Audio/Video Receiver OWNER'S MANUAL AVR 4000 · DIGITAL · PRO LOGIC · 3 STEREO · · 5CH STEREO · · · · · · HALL 1 HALL 2 THEATER VMAx LOGIC 7 SURR. OFF DTS DOLBY D PCM MP3 MUTE RDS PTY CT RT TA AUTO TUNED ST MEMORY PRESET SLEEP O O · VID 1 · VID 2 · VID 3 · VID 4 · DVD · CD · TAPE · FM · AM · 6 CH. L O O 0C0 R O O OPTICAL 1 2 3 COAXIAL 1 2 3 ANALOG VMAx NF 5. 1 LOGIC 7 CM OSD LS O LFE RS O DIGITAL PRO LOGIC 3-STEREO 5 CH STEREO HALL 12 THEATER NIGHT MULTI Test Tone Speaker Channel Digital Select Delay Set Tone Mode ¤ Bass ¤ Surround Mode / ¤ Tuning / Band Preset / ¤ Source / RDS Min Max Power Phones In ­ DIgital ­ In/Out Optical 3 Coaxial 3 S-Video ® Power for the Digital RevolutionTM Table of Contents 3 4 5 7 9 11 14 15 19 19 20 20 21 21 21 23 23 23 24 24 25 25 27 27 27 27 28 29 29 31 32 32 32 33 34 36 36 36 37 37 38 39 39 39 40 40 41 42 42 43 43 43 44 46 56 56 57 Introduction Safety Information Front Panel Controls Front Panel Information Display Rear Panel Connections Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System Configuration Speaker Selection and Placement First Turn On and Use of OSD Settings to be Made With Each Input Used Input Setup Surround Setup Speaker Setup Adjustments for Other Inputs Making Settings independent of selected Input Delay Settings Night Mode Settings Output Level Adjustment Using EzSet Manual Output Level Adjustment Operation Basic Operation Source Selection Controls and Use of Headphones Surround Mode Chart Surround Mode Selection Digital Audio Playback Tape Recording Output Level Trim Adjustment 6-Channel Direct Input Memory Backup Tuner Operation RDS Operation Advanced Features Display Brightness Turn On Volume Level Semi OSD Settings Full-OSD Time Out Adjustment Multiroom Operation Programming the Remote Programming the Remote with Codes Code Readout Learning Codes From a Remote Macro Programming Programmed Device Function Volume Punch-Through Channel Control Punch-Through Transport Control Punch-Through Reassigning Device Control Selectors Resetting the Remote Memory Function List Setup Code Tables Troubleshooting Guide Processor Reset Technical Specifications Declaration of Conformity We, Harman Consumer International 2, route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55013/6. 1990 EN 55020/12. 1994 EN 60065:1993 EN 61000-3-2/4. 1995 Carsten Olesen Harman Kardon Europe A/S 09/00 Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on the front-panel information display 1 ­ (number in a square) indicates a specific front-panel control 0 ­ (number in a circle) indicates a rear-panel connection 0 ­ (number in an oval) indicates a button or indicator on the remote A ­ (letter in a square) indicates an indicator in the front-panel display å ­ (letter in an oval) indicates a button on the Zone II remote 2 TABLE OF CONTENTS Introduction Thank you for choosing Harman Kardon!With the purchase of a Harman Kardon AVR 4000 you are about to begin many years of listening enjoyment. [. . . ] Then, turn the unit off and verify that all speakers are connected to the proper Outputs DE. · When the front left channel is being set at the beginning of the process, EzSet will adjust the main volume level, as shown by the indication of the FRONT L L E V alternating in the onscreen display (if connected) and the Main Information Display Y with the volume indication. During the adjustment, the test tone may seem to pulse, or click, as EzSet changes the level. · As the other channels are set, the channel name and the adjustment offset will appear in the on-screen display (if connected) and the Main Information Display Y. While the level is changing, the Program/SPL Indicator 2 will change colors to reflect the output level in relation to the reference. A red indication shows that the level is too high, while an amber indication shows that the level is too low. When the Indicator is green, the level is correct, and the test noise will move to the next channel. · While adjustments are being made, the red LED under the AVR Selector 5 will flash. After the test noise has circulated once through each channel, it will send the tone to the front left channel once again, to finally adjust its output level. Upon completion of the front left channel adjustment, the Program/SPL Indicator will flash green three times and then go out. Manual Output Level Adjustment Output levels may also be adjusted manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote. Manual output level adjustment is most easily done through the OUTPUT ADJUST menu (Figure 7). If you are already at the main menu, press the ¤ buttons D until the onscreen > cursor is next to the OUTPUT ADJUST line. If you are not at the main menu, press the OSD button L to bring up the MASTER MENU (Figure 1), and then press the ¤ buttons D three times so that the on-screen > cursor is next to the Output adjust line. Press the Set button F to bring the OUTPUT ADJUST menu (Figure 7) to the screen. * F C F S S R R E R U U E OUTPUT O N O R R T N T N R R U T L ER T R RI LE RN ADJUST 0 0 0 0 0 U d d d d d B B B B B * : : IGHT: GHT : FT : TO MEN EFT Figure 7 As soon as the new menu appears, you will hear a test noise circulate from speaker to speaker in a clockwise direction around the room. The test noise will play for two seconds in each speaker before circulating, and a blinking on-screen cursor will appear next to the name of each speaker location when the sound is at that speaker. IMPORTANT NOTE: Because this test noise will have a much lower level than normal music, the volume must be lowered after the adjustment for all channels is made, but BEFORE you return to the main menu and the test tone turns off. After checking for speaker placement, let the test noise circulate again, and listen to see which channels sound louder than the others. Using the front left speaker as a reference, press the </> buttons EU on the remote to bring all speakers to the same volume level. Note that when one of the </> buttons is pushed, the test noise circulation will pause on the channel being adjusted to give you time to make the adjustment. When you release the button, the circulation will resume after five seconds. The on-screen cursor > can also be moved directly to the speaker to be adjusted by pressing the //¤ buttons D on the remote. SYSTEM CONFIGURATION 25 System Configuration Continue to adjust the individual speakers until they all have the same volume. [. . . ] To program the remote for Transport Control PunchThrough, follow these steps: 1. Press the Input Selector 4 for the device you wish to have the channel control associated with and the Mute button b at the same time until the red light illuminates, under the Input Selector 4 and the Program/ SPL Indicator 2 flashes amber. PROGRAMMING THE REMOTE 43 Function List No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Button Name Power Off Power On Mute AVR DVD CD Tape VID 1 VID 2 VID 3 VID 4 Learn AM/FM 6 Ch. Select SPL Sleep Test TV Volume Up Surround Select Night Multi Room Volume Down Channel/Guide / AVR Function Power Off Power On Mute AVR Select DVD Input Select CD Input Select Tape Input Select Video 1 Select Video 2 Select Video 3 Select Video 4 Select Tuner Select 6 Ch Input Select SPL Sleep Test Tone Volume Up Surround Mode Select Night Mode Select Multi-Room Select Volume Down Channel Trim Move/Adjust Up Speaker Adjust Move/Adjust Left Set Move/Adjust Right Digital Input Select Move/Adjust Down Delay Adjust 1 2 3 4 5 6 7 8 Tuner Mode 9 0 Memory Tune Up Direct Tuner Entry Clear Preset Tune Up Tune Down OSD Preset Tune Down DVD Power Off Power On CD/CDR Power Off Power On 1 4 8 12 16 20 5 9 13 17 21 6 10 14 18 22 2 3 7 11 15 19 23 26 DVD Select CD Select 24 25 27 28 31 30 TV/DVD Volume Up Subtitle on/off Sub on/off Volume Down Title Up Menu Left Enter Right Open/Close Down Return 1 2 3 4 5 6 7 8 Chapter 9 0 Audio Angle Clear Slow Forward -/Input Select -/CDP Select -/CDR Select 29 32 33 37 41 45 49 53 57 60 34 38 42 46 50 54 58 61 63 35 39 43 47 51 55 36 40 44 48 52 56 59 62 Speaker/Menu fi Set fl Digital/Exit ¤ Intro/- 64 4000 Delay/Prev. [. . . ]