User manual HARMAN KARDON AVR 35

[. . . ] Select Delay ITAL COAX AC-3 Set TUNING PRESET SCAN PRESET FM MODE DIGITAL PRO LOGIC 3-STEREO HALL 1 HALL 2 THEATER TEST TONE SURR. OFF Mute Bass Treble Balance VIDEO 3 Min Max Min Max L R Video L Audio R Owner's Manual Owner's Manual AVR35 Audio/Video Receiver Table of Contents Introduction. 42 250 Crossways Park Drive Woodbury, NY 11797 ©1998 Harman Kardon, Incorporated Introduction 1 Congratulations!With the purchase of the Harman Kardon AVR35 you are about to begin many years of listening enjoyment. [. . . ] Note that when "small" speakers are used, a subwoofer is required to reproduce low-frequency sounds. Remember that the "large" and "small" descriptions do not refer to the actual physical size of the speakers, but their ability to reproduce low-frequency sounds. If you are in doubt as to which category describes your speakers, consult the specifications in the speakers' owner's manual, or ask your dealer. With the AVR35 turned on, follow these steps to configure the speakers: 1. Put the AVR35 in the Dolby Pro Logic mode by pressing the Dolby Pro Logic Selector Ó on the front panel or by pressing the Surround Mode Selector g on the remote, followed by the / / ¤ buttons h until PRO LOGIC appears in the Main Information Display S and the PRO LOGIC indicator F lights. The words FRNT SPEAKER will appear in the Main Information Display S . Press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel until either LARGE or SMALL appears to match the type of speakers you have at the left front and right front positions, as described by the definitions shown below. When SMALL is selected, lowfrequency sounds will be sent to the subwoofer output only. Note that if you choose this option, and there is no subwoofer connected, you will not hear any low-frequency sounds from the front channels. System Configuration 18 When LARGE is selected, a fullrange output will be sent to the front left and right outputs, and NO low-frequency signals will be sent to the subwoofer output. When you have completed your selection for the front channel, press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to change the display to CEN SPEAKER. Press the Set button j ~ again, and use the / / ¤ buttons h on the remote, or the Selector buttons ¸ on the front panel, to select the option that best describes your system based on the speaker definitions shown above. When CEN SP SMALL is selected, low-frequency center-channel sounds will be sent to the subwoofer output only. Note that if you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the center-channel speaker. When CEN SP LARGE is selected, a full-range output will be sent to the center speaker output, and NO center-channel signal will be sent to the subwoofer output. When CEN SP NONE is selected, no signals will be sent to the centerchannel output. The receiver will operate in a "phantom" centerchannel mode and center-channel information will be sent to the leftand right-front-channel outputs. When you have completed your selection for the center channel, press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to change the display to SUR SPEAKER. Press the Set button j ~ again, and then use the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to select the option that best describes your system based on the speaker definitions shown above. When SUR SP SMALL is selected, low-frequency surround channel sounds will be sent to the subwoofer output only. Note that if you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the surround speaker. When SUR SP LARGE is selected, a full-range output will be sent to the surround-channel outputs, and NO surround-channel signals will be sent to the subwoofer output. When SUR SP NONE is selected, surround-sound information will be split between the front-left and frontright outputs. Note that for optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used instead of Dolby Pro Logic. When you have completed your selection for the surround channel, press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to change the display to S W SPEAKER. Press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to select the option that best describes your system. [. . . ] To remove a macro program, follow steps 1, 2 and 4 above, but do not follow step three. For example, to erase the macro just entered, press the Device Control Selector c and the Mute button ` at the same time until the red light under the Device Control Selector turns on. Press the Power button d, and then press the Channel / / ¤ buttons f. The red light under the Device Control Selector will blink twice to confirm the data entry and then turn off. [. . . ]