User manual HARMAN KARDON AVR 130

[. . . ] ® Power for the Digital Revolution. ® AVR 130 AUDIO/VIDEO RECEIVER OWNER'S MANUAL DIGITAL PRO LOGIC 3 STEREO DSP 5 CH. Select Coaxial AVR 130 AUDIO/ VIDEO RECEIVER 3 4 4 5 7 9 13 13 13 13 14 15 15 16 16 17 17 17 18 19 19 21 21 21 21 22 23 23 23 24 25 25 25 26 26 26 27 27 27 27 28 28 28 29 29 29 29 31 33 42 42 43 43 Introduction Safety Information Unpacking Front-Panel Controls Rear-Panel Connections Remote Control Functions Installation and Connections System Installation Audio Equipment Connections Video Equipment Connections Power Connections System Configuration Speaker Selection and Placement System Setup Speaker Setup Triple Crossover Setting Global/Independent Bass Manager Memory Configuring the Surround Off (Stereo) Modes Output Level Adjustment Delay Settings Additional Input Adjustments Operation Basic Operation Source Selection Volume Control Surround Mode Chart Surround Mode Selection Digital Audio Playback Selecting a Digital Source Digital Bitstream Indications Night Mode Tuner Operation Tape Recording Output Level Trim Adjustment 6-Channel Direct Input Display Brightness Programming the Remote Direct Code Entry Auto Search Method Code Readout Macro Programming Programmed Device Functions Punch-Through Programming Volume Punch-Through Channel Control Punch-Through Transport Control Punch-Through Resetting the Remote Memory Function List Setup Code Tables Troubleshooting Guide Processor Reset Technical Specifications Trademark Acknowledgements Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on the front-panel information display 1 ­ (number in a square) indicates a specific front-panel control ¡ ­ (number in a circle) indicates a rear-panel connection a ­ (number in an oval) indicates a button or indicator on the remote 2 TABLE OF CONTENTS INTRODUCTION Thank you for choosing Harman Kardon®!With the purchase of a Harman Kardon AVR 130 you are about to begin many years of listening enjoyment. [. . . ] When the AVR 130 is in the Stereo Bypass mode, you may still configure the subwoofer output so that it is either turned off, with a full-range signal going to the front left/right speakers, or you may configure it so that the subwoofer feed is activated. The factory default setting is to have the subwoofer turned off for this mode, but you may change that setting by following these steps: 1. Press the / Buttons n on the remote or the </> Buttons ) on the front panel to select the desired option. SUB NONE turns off the feed to the subwoofer, while SUB <L+R> turns it on. When the desired setting has been entered, press the Set Button o@ to return to normal operation. Stereo-Digital Mode When the Stereo-Direct (Bypass) mode is in use, a full-range signal is always sent to the front left/right speakers. By its nature, that option does not pass the signal through the AVR's digital-signal processing, creating the requirement for full-range speakers. If your front speakers are bandwidth-limited, "satellite" speakers, we recommend that you do NOT use the Bypass mode, but rather use the DSP SURROUND OFF mode for stereo listening. To listen to programs in the two-channel stereo mode while taking advantage of the bass management system, press the Stereo Mode Selector 28 until SURROUND OFF appears in the Lower Display Line ¯ and the DSP and SURR OFF Surround Mode Indicators both light up. When only the SURR OFF Surround Mode Indicator is lit, you are in the Stereo-Direct (Bypass) mode. When this mode is in use, the front left/right speakers and subwoofer may be configured to meet the requirements of your specific speakers using the steps shown in the Speaker Setup section on page 16. For accurate calibration, it is a good idea to make these adjustments while seated in your favorite listening position: 1. Put the AVR 130 in the Dolby Pro Logic II mode by pressing the Dolby Mode Selector w on the remote, until one of the Dolby mode names appears in the Lower Display Line ¯. Output level adjustment using the test tone is not available in the Stereo modes. However, in the Stereo-Digital mode, you may trim the output levels using program material, as described on page 26. The test noise will immediately begin to circulate among the speakers in a clockwise rotation, pausing at each position for three seconds. As the test noise rotates, the speaker position will be shown in the Lower Display Line ¯. NOTE: This is a good time to verify that the speakers have been properly connected. As the test noise circulates, listen to make certain that the sound comes from the speaker position shown in the Main Information Display. If the sound from a speaker location does NOT match the position indicated in the display, turn the AVR 130 off using the Main Power Switch 1 and check the speaker wiring to make certain that each speaker is connected to the correct output terminal. After checking for speaker placement, let the test noise circulate, and listen to see which channels sound louder than the others. Using the front left (FL in the display) speaker as a reference, press the / Buttons n on the remote for each channel to begin to bring them to the same level. [. . . ] Button Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Power On Power Off Mute AVR DVD CD Tape VID1 VID2 VID3 Dim AM/FM 6 CH Input Select Sleep Test T/V Volume Up Surround Select Night Spare Volume Down Channel/Guide / AVR Function Power On Power Off Mute AVR Select DVD Input Select CD Input Select Tape Input Select Video 1 Select Video 2 Select Video 3 Select Dim Tuner Select 6 Ch Input Selector Sleep Test Tone DVD Power On Power Off Mute DVD Select CD/CD-R Power On Power Off Mute Tape Power On Power Off Mute VCR (VID1) Power On Power Off Mute TV (VID1) Power On Power Off Mute CBL (VID3) Power On Power Off Mute SAT (VID3) Power On Power Off Mute CD Select Tape Select VCR Select TV Select VID3 Select Channel + Input Select TV/DVD CDP Select Input Level Up CDR Select TV/VCR Volume Up Channel ­ TV/VCR Volume Up Channel + TV/Cable Volume Up Channel ­ Channel + TV/Sat Volume Up Channel ­ Volume Up Surround Mode Select Night Mode Select Volume Down Channel Trim Move/Adjust Up Speaker Adjust Move/Adjust Left Set Move/Adjust Right Digital Input Select Move/Adjust Down Delay Adjust 1 2 3 4 5 6 7 8 Tuner Mode 9 0 Memory Tune Up Next Chapter 9 0 Title Up Menu Left Enter Right Subtitle Down Return 1 2 3 4 5 6 7 8 Input Level Down Up Menu Left Enter Right Exit Down Time 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 Volume Down Up Menu Left Enter Right Exit Down Prev Channel 1 2 3 4 5 6 7 8 9 0 Volume Down Info/Guide Up Menu Left Enter Right Exit Down Prev Channel 1 2 3 4 5 6 7 8 9 0 Volume Down Info/Guide Up Menu Left Enter Right Exit Down Prev Channel 1 2 3 4 5 6 7 8 9 0 Speaker/Menu fi Set fl Digital/Exit ¤ Delay/Prev. 1 2 3 4 5 6 7 8 Tun-M 9 0 Memory Tune Up FUNCTION LIST 31 FUNCTION LIST No. Button Name 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 Direct Clear Preset Up Tune Down D. Skip Preset Down M1 M2 M3 M4 Dolby DTS Surr DTS Neo:6 Logic 7 Stereo Skip Down Skip Up Rewind Play Fast Forward Record Stop Pause Stop Pause Dolby Mode Select DTS 5. 1 Select DTS Neo:6 Select Logic 7 Select Stereo Mode Select Skip ­ Skip + R. [. . . ]