User manual GRANDSTREAM GXW410X

[. . . ] Grandstream Networks, Inc. Analog IP Gateway GXW410x 4 or 8 FXO Ports w/Video Surveillance GXW410x User Manual Firmware Version 1. 0. 1. 2 www. grandstream. com support@grandstream. com TABLE OF CONTENTS GXW410X USER MANUAL WELCOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Gateway GXW410x Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When configured, channel 0 will use this port _value for RTP and the port_value+1 for its RTCP; channel 1 will use port_value+2 for RTP and port_value+3 for its RTCP and so on. This parameter, when set to Yes, will force random generation of both the local SIP and RTP ports. This is usually necessary when multiple GXW410xs are behind the same NAT. This parameter specifies how often the GXW410x sends a blank UDP packet to the SIP server in order to keep the "hole" on the NAT open. IP address or Domain name of the STUN (Simple Traversal of UDP through NATs) server. This radio button will enable GXW410x to download firmware or configuration file through either TFTP or HTTP. Use Random Port Keep-alive interval Use NAT IP STUN Server Firmware Upgrade & Provisioning Via TFTP Server If selected, the GXW410x will attempt to retrieve new configuration file or new code image from the specified TFTP server at boot time. It will make up to 5 attempts before timeout and then it will start the boot process using the existing code image in the Flash memory. If a TFTP server is configured and a new code image is retrieved, the new downloaded image will be verified and then saved into the Flash memory. Note: Please do NOT interrupt the TFTP upgrade process (especially the power supply) as this will damage the device. Depending on the network environment this process can take up to 25 or 30 minutes. Via HTTP Server The URL for the HTTP server used for firmware upgrade and configuration via HTTP. For example, ttp://provisioning. mycompany. com:6688/Grandstream/1. 0. 0. 54 Here ":6688" is the specific TCP port that the HTTP server is listening at, it can be omitted if using default port 80. Note: If Auto Upgrade is set to No, GXW410x will only do HTTP download once at boot up. Firmware Server Path Config Server Path Firmware File Prefix Firmware File Postfix Config File Prefix Config File Postfix Allow DHCP Option 66 to override server IP address or domain name of firmware server. IP address or domain name of configuration server. Default is blank. If set to Yes, configuration file will originate from the DHCP server. Grandstream Networks, Inc. GXW410x User Manual Firmware 1. 0. 1. 2 Page 17 of 32 Updated: 09/2007 Automatic Upgrade Choose Yes to enable automatic upgrade and provisioning. In "Check for new firmware every" field, enter the number of minutes to enable GXW410x to check the server for firmware upgrade or configuration. Other options are: " Always check for New Firmware. " " Check New Firmware only when F/W pre/suffix changes" " Always skip the Firmware check" If set to Yes, config file is authenticated before acceptance. This feature is especially useful for ITSP (Internet Telephone Service Provider) Select the ATA to report the log level. In addition to standard Syslog payload, it contains the following components: GS_LOG: [device MAC address][error code] error message Example: May 19 02:40:38 192. 168. 1. 14 GS_LOG: [00:0b:82:00:a1:be][000] Ethernet link is up Authenticate Conf File Syslog Server Syslog Level NTP server URI or IP address of the NTP (Network Time Protocol) server, which will be used by the phone to synchronize the date and time. If set to Yes, the NTP server will originate from the DHCP server. Allow DHCP Option 42 to override an NTP server Enable Video Surveillance When set to Yes, GXW410x will start converting video feed received from analog camera to IP packets. In order to view this video feed, please follow instructions given under Video Surveillance chapter on page 23. By default it is 554. RTSP Port Grandstream Networks, Inc. GXW410x User Manual Firmware 1. 0. 1. 2 Page 18 of 32 Updated: 09/2007 CONFIGURING THE FXO CHANNELS Configuring the FXO channels on the GXW ­ 410x is an easy process. The Device Status page terms are defined in Table 9: FXO Lines Configuration Definitions. The user has the option to change the default settings as described in the Table 9. [. . . ] Once the "Firmware Server Path" is set, update the change by clicking the "Update" button. If the configured updating server is found and a new code image is available, the GXW410x will retrieve the new image files by downloading them into the GXW410x's SRAM. During this stage, the GXW410x's LED will blink until the checking/downloading process is completed. Upon verification of checksum, the new code image will be saved into the Flash. [. . . ]