User manual GEMINI PS-626X

[. . . ] CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. the exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] You can further modify the sound output of this channel by adjusting the rotary GAIN (12), HIGH (13), MID (14), LOW (15) controls located above the CH 2 SLIDE CONTROL (11). CH 3: To bring this channel into PGM, you must first decide which line will be in use. Once you've selected the proper line, slowly raise the CH 3 SLIDE CONTROL (11) to a comfortable level. You can further modify the sound output of this channel by adjusting the rotary GAIN (12), HIGH (13), MID (14), LOW (15) controls located above the CH 3 SLIDE CONTROL (11). Do not expose this unit to direct sunlight or a heat source such as a radiator or stove. When moving this equipment it should be placed in its original carton and packaging. Plug into the rear panel POWER CORD (2) jack before plugging it into a proper power source. The PS-626x has 2 stereo outputs located on the rear panel: - The MASTER RCA OUTPUT (3) connects the mixer to your main amplifier using standard audio cables with RCA-type connectors. CUE: By connecting a set of headphones to the HEADPHONE (5) jack, you can monitor any or all channels. Use the Toggle switch for CH 1 through CH 3 to assign the CH(s) to be monitored in your headphones. Use the face panel located rotary CUE VOLUME CONTROL (17) to adjust the CUE volume without changing the overall mix. By turning the face panel located CUE/MIX/PGM ROTARY CONTROL (18) counter clockwise you will be able to monitor the assigned cue signal. Slowly turning the control clockwise to middle position allows you to monitor CUE MIX with PGM. Moving the control clockwise to the right allows you to monitor PGM (Main) output. CROSS FADER SECTION: The CROSS FADER (19) allows you to mix from one source to another. The CROSS FADER (19) in your unit is removable and if the need arises can be easily replaced. Your Gemini mixer comes with an RG-45 (RAIL GLIDETM) DUAL-RAIL CROSS FADER, which has internal dual stainless steel rails that allow the slider to ride smoothly and accurately from end to end, and a special mix curve. There are also CURVE and REVERSE controls (20) controls located on the front panel for adjusting the speed in which the audio comes in on each side of the crossfader and the direction each channel comes in from. also available is our RG-45 Pro (RAIL GLIDETM) DUAL-RAIL CROSS FADER. This unique CROSS FADER features, a lighter feel and faster curve specially made for scratching. READ INSTRUCTIONS: All the safety and operating instructions should be read before the product is operated. RETAIN INSTRUCTIONS: The safety and operating instructions should be retained for future reference. [. . . ] HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. La fonction REVERSE vous permet d'inverser le cross fader, ainsile canal 1 sera contôlé par le côté droit du cross fader, et le canal 2 sera contrôlé par le côté gauche. If you do not have internet access, fill out the form below and mail to the appropriate address listed at the right side of this page. IN THE UNITED KINGDOM In the event that you need service on your Gemini product under warranty, simply write a letter describing the problem, along with your contact information. [. . . ]