User manual GEMINI MM-03

[. . . ] ATTACHMENTS: Do not use attachments not recommended by the product manu facturer as they may cause hazards. WATER AND MOISTURE: Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. ACCESSORIES: Do not place this product on an unstable cart, stand, tripod, brack et, or table. The product may fall, causing serious injury to a child or adult, and seri ous damage to the product. [. . . ] Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceil ing. HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as This state of the art mixer is backed by a three year warranty, excluding crossfader and channel slides. The crossfader and channel slides are backed by a separate 90 day warranty. - 4U 19" rack mounted club mixer - 5 stereo Channels - 8 line, 3 Mic, 2 convertible phono/line, RCA inputs - 3 band rotary line EQ control per channel with cut feature - Fully removable, user replaceable Rail Glide crossfader - Assignable cross fader - Rotary gain control per channel - Dual display with bright LED - Push-button cueing with cue/PGM fader control - Rotary master, zone, balance & cue volume controls - Master, zone & record RCA outputs - Balanced master output - XLR-1/4" combo Mic input - 2 band rotary Mic EQ control with cut feature - Rotary Mic volume control - Auto Talk-Over feature - Face plate located 1/4" headphone input - The REC (4) output jacks can be used to connect the mixer to the record input of your recording unit, thus enabling you to record your mix with RCA cables. Located on the rear panel are 2 Phono(PH)/Line(LN) convertible RCA inputs (13, 16), and 6 line RCA inputs (7, 8, 9, 14, 17, 18). The convertible RCA inputs for CH 2 (38) & CH 3 (45) allow PH and LN level equipment to be connected to the mixer. When using (a) turntable(s), you will need to ground the RCA cable(s) by screwing in the grounding fork(s) to the GROUNDING SCREW (11) located in the back panel of the MM-03 mixer. The stereo LN INPUTS only accept line level inputs such as a CD, DAT, MiniDisc, etc. All operating instructions should be read before using this equipment. In the USA ~ if you experience problems with this unit call Gemini Customer Service at: 1 (732) 738-9003. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove. When moving this equipment, it should be placed in its original carton and packaging. Headphones may be plugged into the face-plate located 1/4" HEADPHONE JACK (60). Once all of your connections have been in the rear panel, turn on the mixer by pressing the POWER SWITCH (70). CHANNEL 1: To bring this channel in to program output (PGM), you must first decide which line will be in use. Use the LN SWITCH (25) to toggle from LN 1 (18) to MIC 2 (19) on this channel. Slowly raise the CH 1 SLIDE CONTROL (31) to a comfortable level, once you've selected the proper line. You can further modify the sound output of this channel by adjusting the rotary GAIN (26), HIGH (28), MID (29), LOW (30) controls located to the left of the CH 1 SLIDE CONTROL (31). [. . . ] The tone and decibel level of MIC 2 (19) and MIC 3 (10) are controlled by the CH 1 (31) and CH 4 (52) slide controls, the 3 BAND ROTARY EQ (HIGH (28, 49), MID (29, 50), LOW (30, 51)) controls and GAIN (26, 47) rotary controls, respectively. TALKOVER: The purpose of the AUTO TALKOVER MODE is to allow the program playing to be muted so that the mic may be heard above the music. The MIC/TALKOVER SWITCH (24) controls MIC 1 (20) with 3 settings: - When the MIC/TALKOVER SWITCH (24) is in the BOTTOM position, MIC 1 (20) and TALKOVER MODE are all OFF. VU METER: The VU METER (65) indicates the program output level of the MASTER (3) left and right stereo levels. [. . . ]