User manual GEMINI CDM-3600

[. . . ] CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. READ INSTRUCTIONS: All the safety and operating instructions should be read before the product is operated. [. . . ] Do not use this CD player at temperatures below 41°F/5°C or higher than 95°F/35°C. The apparatus should not be exposed to dripping or splashing, and no objects filled with liquids such as vases should be placed on the apparatus. When disconnecting the power cord from the AC outlet, always grasp it by the plug. To prevent electric shock, do not remove the cover or the bottom screws. HEADPHONE OUTPUTS: The HEADPHONE OUTPUTS located at rear center and front center of the CDM-3600 will accept any headphone with a standard 1/4" connector and or adaptor and will allow you to CUE your music program before you play it, you can adjust the volume and PGM mix of the HEADPHONE (see CONTROLS) below. MIC (MICROPHONE) INPUTS: The main MIC or Microphone inputs are located at the back right hand corner and front panel of the CDM3600 and will accept any balanced and unbalanced XLR as well a standard 1/4" connector. MASTER XLR OUTPUT (BALANCED): Allows you to connect balnced XLR cables to MASTER OUTPUT of the CDM-3600 both the RCA and XLR outputs can be used at the same time but are both controlled via the same MASTER OUTPUT. MASTER /RECORD RCA OUTPUT (UNBALANCED): The MASTER RCA output connects the mixer to your main amplifier using standard audio cables with RCA-type connectors. The RECORD RCA OUTPUT output jacks can be used to connect the mixer to the record input of your recording unit, thus enabling you to record your mix with RCA cables. POWER: Once you have connected all your cables and made sure that the VOLTAGE SELECTION SWITCH is set correctly, you can turn the CDM-3600 on by pressing the POWER button, pressing the CDM-3600's POWER button a second time will turn off the unit. VOLTAGE SELECTION SWITCH Before plugging the CDM-3600 into any wall outlet, make sure that the VOLTAGE SELECTION SWITCH is set to the proper voltage. To change this selection unscrew the hard plastic protective top with a Phillips head screw driver. Then use a flat head screw driver to move the switch to the proper selection (115V or 230V) . Excessive force may cause damage, if the switch does not move smoothly, contact a qualified technician. DISC TRAY: The DISC TRAY is where the CD is held during loading, unloading and playback, and holds both 12 cm and 8cm CD's. (DO NOT FORCE THE CD TRAY TO CLOSE EXCESSIVE FORCE WILL DAMAGE THE CD MECHANISM, USE THE OPEN AND CLOSE BUTTONS) EJECT BUTTON: Pressing the EJECT BUTTON will open or close the DISC TRAY, unless the CDM-3600 is in play mode, then you must first stop the side you wich to eject. JOG WHEEL : In SEARCH MODE the JOG WHEEL can be used to search forward or bacwards in the music track, as well as for fine adjustments to a CUE point in PAUSE mode. In PITCH BEND mode the JOG WHEEL will function the same as the PITCH BEND allowing you to speed up (FORWARD) or slow down (REWIND) the music clockwise bieng (FORWARD) and counter clockwise being (REWIND). DISPLAY: The DISPLAY shows the track number, pitch value, pitch bend, single, continue (for continuous play), play/pause modes, fast forward/reverse modes, loop mode, reloop mode, PGM, repeat modes, the playback display bar, and three diffirent time displays. These times displays are TIME ELAPSED on the track, TIME REMAINING on the disc and and TIME REMAINING on the track. To program a set list into the CDM-3600 memory, begin by stopping the unit from play and pressing PGM to begin the set list. Select a track by using the track selection button to scan to the first track to be placed in the set list. [. . . ] When the CROSSFADER is moved all the way to the opposite side of the currently playing disc, the unit will stop playing that disc and return to the beginning of the track or the set cue point. At the point which you wish to start the audio from the Cued CD, simply move the CROSSFADER in the direction of the Cued CD player, and playback will begin. IN THE UNITED KINGDOM In the event that you need service on your Gemini product under warranty, simply write a letter describing the problem, along with your contact information. Make sure to enclose a copy of your receipt for proof of warranty information. [. . . ]