User manual FUTABA 2PCKA

[. . . ] Before using your 2PC / 2PCKA, read this manual carefully and use your R/C set safely. After reading this manual, store it in a safe place. APPLICATION, EXPORT, AND RECONSTRUCTION 1. The product described in this manual is subject to regulations of the Ministry of Radio/Telecommunications and is restricted under Japanese law to such purposes. Exportation precautions (a) When this product is exported from Japan, its use is to be approved by the Radio Law of the country of destination. [. . . ] Interference from other R/C systems will cause loss of control. Safety Precautions Prohibited Do not operate when you are tired, not feeling well or under the influence of alcohol or drugs. Your judgement is impaired and could result in a dangerous situation that may cause serious injury to yourself and others. Before you turn on the power switch on the transmitter, always check to see that the trigger is at the neutral position. When you turn the system off, always turn the receiver off first then the transmitter. If this procedure is not followed, injury to yourself and others as well as loss of control could occur. Safety Precautions Adjustment Note Make all adjustments to the radio control system with engine not running, or the electric motor disconnected. If the engine is running or the motor is connected while adjustments are made the model may run out of control. Remove the main battery source from electric powered models when they are not being used. Should you accidently leave the receiver switch on the model could run out of control. Caution Do not touch Do not touch the engine, motor, speed control or any part of the model that will generate heat while running. Touching hot parts will result in serious burns. Storage And Disposal Safety Precautions Warning (When using a Ni-cad battery to power your system) At the end of a days operation store the system with Ni-cad battery discharged. You should fully discharge your systems batteries periodicity to prevent a condition called "memory". For example if you only make two run in a day or you regularly use a small amount of the batteries capacity, the memory effect can reduce the actual capacity even if the battery is charged for the recommended amount of time. Prohibited Do not throw a Ni-cad battery into a fire. Overheating, damage and acid leakage may lead to burns, loss of eye sight as well as numerous other types of injuries. Should you get even the smallest amount of the electrolyte in your eyes, Do Not rub, wash immediately with water, seek medical attention at once. If electrolyte comes in contact with your skin or clothes, wash with water immediately. Caution Prohibited Do not store your R/C system where it will be exposed to the following conditions. · Extreme heat or coldness · Exposed to direct sunlight · Where humidity is high · Where vibration is prevalent · Where dust is prevalent · Where there is steam and condensation · Where the system would be exposed to engine exhaust Storing your R/C system under adverse conditions could cause deformation and numerous other problems with operation. (When using a Ni-cad battery to power your system) Caution When disposing Ni-cad batteries, cover any exposed contacts with some type of insulation to prevent short circuit. Some states require special handling when Ni-cad batteries are disposed. Contact the State Agency responsible for recycling hazardous waste for the procedures in your state. Other Safety Precautions Caution When operating two or more models at the same time, have a third person act as a spotter. They will be in charge of safety and you should follow their instructions. Beginners should receive instructions regarding safety and operation from an experienced modeler. Use genuine Futaba parts only. Always use only genuine Futaba receiver, servos, electronic speed controls along with other optional parts and components. Futaba will not be held responsible for damages caused by other than genuine Futaba parts and components. Use only genuine Futaba parts and components listed in the instruction manual and catalog. (When using a Ni-cad battery to power your system) Prohibited Do not short circuit the Ni-cad battery terminals. Short circuiting the terminals will lead to sparks and overheating and could cause a fire and burns as well. Safety Precautions 2PC / 2PCKA Before Operation System Contents After opening the container, check the contents for the following items. [. . . ] Reversing The Servo Operation Direction Should the servo operate in the opposite direction required for your application, reverse the rotation with the reversing switch. N R SERVO REV SW Steering N Side: Normal R Side: Reverse Throttle N R TH. N Side: Normal R Side: Reverse Assembly / Adjustment (Reversing Switches) 1 Set the servo reversing switch on the transmitter to normal side. 2 Turn the high point trim fully clockwise. (Neutral Adjustment) MC210CB Fully Clockwise * Adjust the Amp with the mini screwdriver supplied with this system. *(forcing the adjustment trims past their stop will cause internal damage to the speed control. ) 3 Have the throttle trigger at neutral. [. . . ]