User manual FLYMO VENTURER 320

[. . . ] FO T IN TA N ce P O R ore use feren I M bef re re ad futu Re for tain & re IO M AT R N For all customer enquiries or for replacement parts, contact:- 01325 300303 www. flymo. com eop. customer. services@electrolux. co. uk ¤ 1 Carton Contents start/stop lever cable clip nut (if applicable) lock off button upper handle plastic handle knob grassbox upper grassbox lower electric cable with moulded on plug spanner/scraper tool roller & rear height adjustment assembly (1 lever each side) instruction manual switchbox washer bolt lower handles safety flap lower handle fixing screws motor cover wheel assembly (x2) deck IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this lawnmower can be dangerous!This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. [. . . ] The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. non-detachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. Assembly Instructions A ensure the point of the screw stays inside the handle. Assembly of Lower Handles to Deck 1. Using a pozidrive screwdriver, secure the screws into the lower handles, ensuring the point of the screw stays inside the handle. Insert lower handles with screws attached, into the deck and fully tighten screws. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost. Ensure the upper handle and the lower handle are aligned correctly. (C) 3. Make sure the cable is not trapped between the upper and lower handles. Ensure all clips are securely connected. B C D 4 Cutting Height Adjustment Wheels - Front Cutting Height Adjustment · Height of cut is adjusted by raising or lowering the front wheels and rear roller. · NOTE The wheels and the roller must be adjusted to the same position: HEIGHT OF CUT WHEEL ROLLER Low Hole 1 Position H Medium Hole 2 Position J High Hole 3 Position K · NOTE A medium height of cut is recommended for most lawns. To remove the wheel assembly turn the wheel hub in an anti-clockwise direction. (E) 2. Select one of the 3 holes in the mounting plate and note it as the other wheel will need to be adjusted to the same position. (F) 3. Locate fixing bolt through hole in hub cap, wheel and selected hole in mounting plate. (F) 4. Turn the wheel hub in a clockwise direction until the wheel assembly is securely located to the deck. (E) 5. Using the same height adjustment position repeat the procedure for the other wheel. Select one of the 3 locations and note it as the other lever will need to be adjusted to the same position. Lift the lever out of location and rotate the roller to the desired position. Using the same height adjustment position repeat the procedure for the other lever. E to remove turn anti-clockwise to fit turn clockwise F mounting plate wheel hub cap 1 2 holes 3 fixing bolt G H J K Grassbox Fitting Fully Assembled Grassbox to Lawnmower. Locate fully assembled grassbox onto 2 location points at the rear of the deck 4. AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. · For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. The design of the safety flap permits the cut grass to be discharged downward behind the machine. L 5 Starting and Stopping M N To Start your Lawnmower 1. To secure, position loop over the hook and pull the cable back through the slot (N). [. . . ] * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Blades, Electric Mains cable. Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way EC Declaration of Conformity I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. [. . . ]