User manual FARSTONE RESTOREIT 7.1

[. . . ] RestoreIT® User's Guide Copyright Notice Copyright© 2006 FarStone Technology, Inc. No part of this publication may be copied, transmitted, stored in a retrieval system, or translated into any language in any form or by any means without the expressed written permission of FarStone Technology, Inc. FarStone grants you the right to use one copy of the enclosed software program ("SOFTWARE") on a single computer. If the SOFTWARE is installed on a network, or more than one user can run the SOFTWARE at the same time, you must purchase an additional license for each additional user or computer. [. . . ] Password Required to access RestoreIT Check this box to enable password protection for the program. Set a password for RestoreIT to protect your program settings from being modified by unauthorized uses To set/change the password, click Set Password, and then enter your current password (by default there is no password set). Enter the new desired password (maximum of eight characters) and re-enter it to confirm your password. After the password is applied, RestoreIT will ask for a password upon starting the application. If you enter a wrong password five times RestoreIT will shut down automatically (you can try again by restarting the application). Please memorize your password and keep it confidential. · · · RestoreIT Scheduler RestoreIT provides flexible and easy-to-use schedule settings. There are two options for this category. Backup Scheduler This option allows you to configure a schedule for creating your Incremental Backup Points. Creating a Backup Point Automatically Check the Create Incremental Backup Point Automatically box to enable this function. · Create a new Backup when the system starts up: Using this option, your PC will create a Backup Point automatically every time the system starts up. After selecting this option, your PC will create a Backup Point every (number) of day(s) that you have set. For example, if the setting is for every two days and your PC does not start up within six days, when you start up, RestoreIT will create only one Backup Point automatically. Using this option, RestoreIT will create a Backup Point every time you boot up. Create Backup Points while the system is running: Using this option, RestoreIT allows you to create Backup Points while you are using your computer. You can set RestoreIT to create a Backup Point every 1 to 720 hours. · Note: During the RestoreIT Backup Point creation process, any program reading from or writing to your hard drive may affect the creation of the Backup Point. At anytime if there are any possible conflicts, RestoreIT will stop creating the Backup Point and will not affect normal operations. Restore Scheduler This option allows you to set a restore schedule and enables you to restore your system at a pre-set schedule. Restoring to a Backup Point Automatically If you would like to let RestoreIT restore to a specified Backup Point automatically, check the Restore Automatically check box to enable this function and at the same time, specify the backup point to restore and the restore mode. The number in the box indicates the ID number of an Incremental Backup Point in the Backup Point list. (Please refer to chapter 3-5 Managing Backup Points for more information). · · Restore at system startup: Your computer will revert to a specified Backup Point automatically every time the system reboots. You can schedule RestoreIT to: Restore system every (number) of day(s). After selecting this option, your PC will revert to the specified Backup Point every (number) of day(s) that you have set. However, if for example, you schedule RestoreIT to restore the system every two days but you do not start your PC for six days, when you start your system, RestoreIT will create only one Backup Point, and will restore your computer back to the specified Backup Point. Using this option, RestoreIT will automatically restore your computer to the specified Backup Point every time you reboot your system. [. . . ] If the "Software" is an upgrade from other "Software", whether from us or another supplier, you may use or transfer the "Software" only in conjunction with the upgraded "Software", unless you destroy it. If the "Software" is an upgrade from FarStone, you may only use that upgraded "Software" in accordance with this License. Where a database is included with the "Software", you acknowledge that it is licensed only in connection with the use of the "Software" to perform disk creation, and that the database and all data derived there from must be maintained in confidence in accordance with the provisions of Section E of this document. This License does not grant you any rights to distribute or disclose such a database or data contained therein. [. . . ]