User manual FAGOR NC-200 PB OPERATION

[. . . ] FAGOR NC-200 PB NC FOR PRESS BRAKES OPERATING MANUAL Manual version 0111 INDEX Diagram of a typical press BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Description of the various machine models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 1 2. 2 2. 3 2. 3. 1 2. 3. 2 2. 3. 3 2. 3. 4 2. 3. 5 3 3. 1 3. 1. 1 3. 1. 2 3. 1. 3 3. 1. 4 3. 2 3. 2. 1 3. 2. 2 3. 2. 3 3. 3 3. 3. 1 Unit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If any axis does not have a home switch, usually the Y, this unit requests the password 719200 to access the mode and assumes that the values set by the OEM are to be modified. This is only recommended in case of a breakdown or when updating this unit's software version. For the affected axis, proceed as described in section 3. 2. 1b 3. 2. 3 SEQUENCE FOR THE Y AXIS. At the reference position, bend to the bottom until the ram is stopped and press to balance the reading of the axes Y-Y'. b. - With a linear potentiometer. 1- Press and it displays the potentiometer value in volts in MANUAL mode. 2- Press 3- Move the "Y" axis with to the far end position, towards Y-. Activate the BEND foot switch again up to the final position. Press Press again. to exit. Page: 18 - Operating Manual - NC-200 PB 3. 3 TOOL TABLE LOADING With this NC, it is possible to load the data of up to 10 sets of punches and dies. This data refers to the height of the punch (from 0. 000 mm and 9999. 999 mm), to the height of the die, width of the die, "V" (from 0. 000 mm to 9999. 999 mm), die angle that limits the bending depth and its edge radius (from 0 to 99. 9). To do this: - Access the editing mode by pressing The screen shows three options: Select "Punch" and press - Choose the tool number using - Indicate the punch height: - Press to exit. - Indicate the die aperture with: - Indicate the die height with: - Indicate the die angle with: - Indicate the die edge radius with: - Press to exit [value] [value] [value] [value] · Before quitting this mode, it is recommended to check that none of the 9 table positions contains data exceeding the range with a code EEEEEEEE. By default, the whole table contains some initial values: Hpunch = 0, Hdie = 0, A = 16, r = 1. 6 that may be recalled. 3. 3. 1 RECALL INITIAL TOOL VALUES While in punch or die editing mode, press the sequence: F F The unit will request confirmation of this command. Select <Yes> and press to restore the initial values. NC-200 PB - Operating Manual - Page: 19 4 PROGRAMMING This NC can store up to 200 program blocks. The program memory may be locked setting installation parameter PAR51(1)=1 This way, the program blocks cannot be edited or deleted. In the initial teach-in stage, it is recommended to work with the simple resources only as a positioning dro without attributes and with a material factor M0 which only compensate for the rounding radius Rex = sheet metal thickness. Once familiarized with them, it is possible to expand the resources of the materialtype tables, program ANGLES with the same capabilities as specific CNC's for press brakes. To access this simple mode (without attributes): (The assumes the default values of D and T set by PAR29 and PAR30). · Press 5 1 · Press 8 to activate the bit and confirm with · Exit by pressing Programs edited in conversational mode keep the attributes even when not displayed in EDITOR mode if PAR51. 8 has been activated 4. 1 PROGRAM EDITING In a program, it is possible to "Edit" new blocks, "Modify" the data already programmed in the blocks or "Delete" all their contents leaving them free (empty). 4. 1. 1 EDITING / DELETING AN EXISTING PROGRAM Press mode. to access the block editing Edit Prg Punch Die - Select "Prg" using the press keys and Program Editing Program . . . . : 0000 - Use the keys to select the desired program to be modified (they are not stored sequentially). Press Program Editing Program . . . . : 0007 - Page: 20 - Operating Manual - NC-200 PB - Use the (Edit or Delete). Select "Delete" Select "Edit" keys to select the option Program Editing Edit Delete to delete a program from memory. . to modify. . · · · It access the program block N0. Only some values of the parameters affecting the geometry of the bend may be modified: Die number (with different width). [. . . ] Die number Sheet metal thickness Pressure (LF) Bend position Block execution number Delay between blocks (timing). Auxiliary output H (high) X axis retract Punch delay at the end of the bend (Delay) Top dead point (up) 6. 4 TRANSMISSION OF MATERIAL-TYPE TABLES In <Send> mode, this NC can send the full table stored in it out to a PC. In <Receive> mode, this NC can receive one or several materials M00 through M19 from a PC. NC-200 PB - Operating Manual - Page: 33 APPENDIX ERROR CODES Message FAGOR dro Description Power outage or turned off by main switch after saving the data. Power outage or turned off by main switch without having saved the data. [. . . ]