User manual FAGOR LFU-45IT

[. . . ] RINSE AID WARNING LIGHT Illumination of this light signals that rinse aid dispenser is empty. EXTRA PROGRAM BUTTON This button gives access to the one of the five extra programs (see table). EXTRA PROGRAM LIGHT Illuminates to indicate that one of the five extra programs (see table) is going to be executed. PROGRAM DELAY BUTTON Press this button to delay the start of the program by up to 9 hours. [. . . ] Press the button several times in succession and the display will show the delay with which the appliance will start, beginning from 9 hours. 2 END 3 45 7 6 9 8 1 MIX P 45 CANCELLING THE CURRENT PROGRAM · To cancel the currently selected program, open the door and hold down the PROGRAM SELECTION (3) button for a few seconds until the indicator lights for programs 4 and 5 illuminate simultaneously (the word "end" is displayed on the window). END MIX 45° 55° 65° 70° · · Close the door. After approximately 1 minute the dishwasher will advance to the end of cycle. CHANGING THE PROGRAM To change the program in progress, simply open the door and select a new program. When the door is closed the dishwasher will automatically select the new program. AND PROTECT THE ENVIRONMENT · · · · · Always try to run the dishwasher fully loaded. Use the washing program that is most appropriate for each type of load. If available, connect the dishwasher to a hot water supply up to 60°C. TO CUT DOWN ON DETERGENT CONSUMPTION!AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: · · separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; do not pour the detergent directly on the dishes. If the door has to be opened while washing is in progress, the program will be interrupted. The relative light will keep flashing and a beeper will signal that the cycle has not been completed. You must wait about 1 minute before closing the door to restart the program. When the door is closed the program will continue from where it was interrupted. This operation should only be carried out if strictly necessary, because it might cause problems in execution of the program. 33 User instructions 2 END 3 45 7 6 9 8 1 MIX P 45 ADJUSTING THE WATER SOFTENING SYSTEM N. B. : for the setting below to be possible, a washing program other than the soak program must be set. Press the PROGRAM DELAY button (8) and keep it pressed until the preset value appears followed by a full stop (normally 3. ). Release the button then press it again in succession to display the value required, referring to the table. The 6 setting levels available will appear in this order: 3. , 4. , 5. , 0. , 1. , 2. . When the value required appears on the display, release the button; after 5 seconds the system automatically returns to setting of the program delay, and the setting will be made with the chosen value. N. B. : the display shows the water hardness setting and the program delay. The dot (. ) after the number indicates that the water hardness setting is being displayed. WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degrees (°dF) 0-5 6 - 11 12 - 21 22 - 33 34 - 45 46 - 53 0-9 10 - 19 20 - 36 37 - 59 60 - 79 80 - 107 SETTING 0. 5. Contact your local water board for information on the hardness of your water supply. [. . . ] · · Alarms E1, E3, E4 interrupt the current program immediately. The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program. To "reset" an alarm is necessary: · Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again. If the malfunction persists, contact your authorised Service Centre. 37 Allineare al bordo s uperiore del pannello porta. Mit der Oberkante der Dekorplatte fluchten. Zet hem op één lijn met de bovenste rand van het durpaneel. [. . . ]