User manual FAGOR IF-900S

[. . . ] Glue the foam joint underneath the hob plate following the outline of the support surfaces with your worktop. 4 40 40 C60T376A8. qxd 14/3/07 16:21 Pgina 5 FRAME DIMENSIONS 65 65 930 490 510 40 mx. 490 770 510 40 mx. 900 750 288 65 930 410 65 51 440 40 mx. 0 60 mx. 900 270 5 49 0 C60T376A8. qxd 14/3/07 16:21 Pgina 6 3 FASTENING TO THE WORKTOP A Fit the hob into the space in the unit pressing down well to close the seal properly. B Fix the four hob plate hooks underneath in the unit space corners. 4 INSTALLATION POSITION There must be a current of fresh air to cool your induction hob's electronics circuits as shown in the diagram. 40mm minimum 5mm minimum 5mm minimum 50mm Hob on oven 50mm Hob on unit IMPORTANT Installation must guarantee that fresh air can come from the rear and that a vent measuring at least 5 mm allows the air to escape in the front part. 6 C60T376A8. qxd 14/3/07 16:21 Pgina 7 USING INDUCTION HOBS USE 1 TYPE OF APPLIANCE TYPE A Type "A" appliances have commands with special functions or with basic functions TYPE B Type "B" appliances have compact commands POWER OF EACH HOB Hob size (cm) 16 18 21 28 Type "A" power 2. 200w 2. 800w 3. 100w 3. 600w Type "B" power 2. 000w 2. 800w 3. 100w 2. 800w 7 C60T376A8. qxd 14/3/07 16:21 Pgina 8 2 DESCRIPTION OF THE COMMANDS Find the type of command which corresponds to your hob . Compact command COMMAND WITH SPECIAL FUNCTIONS A On/Off Sensor B Power sensors and displays between "0 and P. " C Indicator of Hob to use. [. . . ] 5. Once the time has passed, return to the initial position and the dot will disappear. BOOSTER The cooking areas are equipped with a "BOOSTER" function. This function means that the maximum temperature can be obtained quickly. 1. Press the button The hob power display will display (bo) and the hob will start to give maximum power. 2. Once the hob has heated up, select the chosen power level by pressing the "-" button in zone "B". The "BOOSTER" function will be cancelled by pressing any other power sensor associated with the hob, or with the on/off sensor. IMPORTANT By using the "BOOSTER" function, if the other hob is switched on the same side of the hobplate, the maximum power level which can be used is 6. This is due to the fact that in this function the appliance takes power from the adjacent hob. 11 C60T376A8. qxd 14/3/07 16:21 Pgina 12 OFFSET PROGRAMMING This allows you to adjust the finishing time and the duration of this cooking session. ADJUSTING THE CURRENT TIME: Use the "-" and "+" power buttons in zone (B) to change the hour and use the "-" and "+" timer buttons (E) to adjust the minutes. Validate the time by pressing the button (the digits will then flash). Adjust the time to when you wish cooking to finish with the " -" and "+" buttons from zones (B) and (E). Adjust the cooking time using the "-" and "+" buttons in zone (E). Define the chosen power level for cooking with the "-" and "+" buttons from zone (B). Once programmed, it displays (Auto) and then the digits go off and only a red dot remains lit. IMPORTANT Offset programming cannot be used at the same time on more than one hob. The chosen finishing, duration and power values must be changed whilst the digits are flashing. 12 C60T376A8. qxd 14/3/07 16:21 Pgina 13 COMMAND WITH BASIC FUNCTIONS A On/Off sensor. A B C D D Safety sensor and display. OPERATION SWITCHING ON A HOB The operation is the same as described for the commands with special functions. TIMER OPERATION The operation is the same as described for the commands with special functions. ACOUSTIC SIGNAL The operation is the same as described for the commands with special functions. FUNCTION (P point) (Fast heating function) This function allows greater power to be obtained during a certain time. The "P. " function (P point) is obtained by pressing the "+" button as far as the "P. " position, release the command and the "P. " will flash, press the command again and it will be put in the maximum power "P. " position (P point) then press the "-" command and enter in the chosen cooking time. When the relevant time has passed, the power selected by the user will return. IMPORTANT After selecting the power "P. " (P point), if you do not choose the final working power, the hob power will be maintained at "P. " Whilst "P. " is displayed (P point) any action on the power commands will cancel the "fast heating function" and it will return to the classic power regulation mode WARNING Preferably use cooking zones situated on different sides. [. . . ] The plate does not work and this information appears The plate stops working, it beeps every 10 seconds and or F7 appears on screen. WHAT TO DO Check the electrical installation. Check fuses and trip switches. See chapter on recipients for induction. New appliance The electronics circuit does not work properly. The plate is locked. There has been an overflow or an object is obstructing the command panel. [. . . ]