User manual FAGOR FWD612IT

[. . . ] c Cover the holes with the plastic covers you have just removed. a/c Important Do not throw the blocking screws away. You may need to move the washing machine at a later date. 72 2 CONNECTION TO THE MAINS WATER SUPPLY AND DRAINAGE installation and assembly CONNECTION TO THE MAINS WATER SUPPLY The water supply hose is inside the drum: a Connect the bent end of the hose to the threaded inlet of the electrovalve located at the rear of the washing machine. Then securely tighten the connection nut. It is important that the drain hose bend is correctly fastened to the outlet, to prevent any risk of it becoming detached and causing flooding. If your washing machine has a hot water intake, connect the hose with the red threaded end to the hot water tap, and to the electrovalve with the red filter. [. . . ] Each time the button is pressed the start of washing is delayed by 1 more hour. Cancelling the delay To cancel the delay you have to press the clock button successively. The delay will be cancelled when 24 hours have been reached and the button is pressed once more. If the programme is changed the delay is also cancelled. Select ADDITIONAL FUNCTIONS Additional function selection button depending on programmes. b By pressing the button several times you can choose between several combinations of one, two and up to three additional functions at the same time depending on the programme selected. Button: Easy-iron ( ) This option prevents garments from creasing by means of carrying out a special programme with special turns to fluff out the garments after spin-drying and make them easier to iron. Button: Extra rinse ( ) Increases the level of the final rinse obtained in the clothes; suitable for large loads and garments belonging to people with sensitive skin. Button: Intensive wash ( ) This option, specially recommended for heavily soiled, stained clothes, achieves better results by extending the normal wash cycle. a Select b Select Important 83 If during the additional function selection, the programme is changed or the ON/OFF button is pressed, all the functions selected until then are cancelled. 6 STARTING UP AND SELECTION BLOCK FUNCTION STARTING UP using the appliance a Start/pause button a To start up the washing machine you have to press the start/pause button. The minutes remaining until the end of washing and drying will appear on the display at all times. Select BLOCK FUNCTION a Block function selection The lock function ensures that the programme will not be affected if any buttons are pressed. The block function should be activated after the wash programme has been selected together with all its options. Activating the block function a The block function is activated by pressing the start/pause button and holding it down for at least 3 seconds. Deactivating the block function b The block function is cancelled when the wash programme comes to an end. If you want to deactivate the block function before the end of the programme, you have to hold the start button down again for at least 3 seconds. After 3 seconds, the block function indicator will disappear from the display, and it will go into pause status. The ON/OFF button does not cancel the block function. Select b Select 84 7 WASH PROGRAMME PHASES AND POWER CUTS PROGRAMME PHASES When the programme is running, the programme phase and the time remaining for it to end will appear on the display. . The active phases will appear successively at the top of the display as the programme progresses. The time remaining until the end of the programme will also appear on the display. Any option button can be selected provided the wash phase in which it takes effect has not been passed and when the programme accepts the option. Pressing the delay button during washing will have no effect on the washer-dryer. Pressing the start/pause button during the wash activates the PAUSE function. If the programme is changed on the selector dial during the washing and drying process, the washer-dryer will go onto PAUSE status and the programme will be cancelled. If you need to add or remove a garment, press the start/pause button and make sure that the water level is not above the door overflow level and that the temperature inside is not high. [. . . ] This is why the hatch cannot be opened for 2 minutes. Why doesn't the remaining time shown on the clock coincide with the real time left until the selected cycle finishes? This time is for guidance purposes only and may be affected by the conditions under which the selected programme is being run, e. g. initial water temperature, size of load or unbalance caused by the garments during spin drying. Other indications The washing machine can detect other indications. When this happens a number of other indicators appear on the display: F05, F06. . . , F10. If this happens, call the Official Technical Service. 90 washing machine eco-note When your appliance is of no further use, it should not be disposed of together with general domestic waste. [. . . ]