User manual FAGOR FU-7814

[. . . ] Follow the washing instructions recommended by the manufacturer of the garment to be washed. Do not turn your washing machine on until you are sure that: It has been installed in accordance with the installation instructions. All the water, drainage, mains electricity and earth connections meet the local regulations and/or other applicable regulations. 70 washing machine Work top Detergent dispenser specifications Power cord Control panel Drain hose Hatch Filter Kickplate Levelling feet ACCESSORIES LOCATED INSIDE THE DRUM Stainless steel drum Rear plugs Drain pipe bender 71 Water inlet hose washing machine 1 UNPACKING AND UNBLOCKING THE WASHING MACHINE UNPACKING a Remove the base, corner protectors and top cover. [. . . ] It can be modified by pressing the spin drying button and the number of revolutions will be reduced by 100 revolutions at a time to 400. Anti-crease option The wash programme stops on the last rinse, with the clothes left in water. When the function is deactivated, the washing machine continues the programme, draining and spin-drying. It is used, for example, when you are not at home and want to delay the spindrying until you get home, to prevent the clothes creasing after spin-drying and being left in the drum to be removed. b c d c d a OPENING THE HATCH a b Depending on the model, you can open the hatch by pressing the hatch opening button. If you cannot open the hatch due to a breakdown or a power cut, proceed as follows: remove the dispenser by pulling the handle outwards and pressing the blue lever with your finger. Turn the button to the left with the aid of a coin and the hatch will open. If your model of Washing machine does not have remote opening you have to await about 2 minutes from the end of the programme before being able to open the hatch. b 82 5 TIME DELAY SECTION AND ADDITIONAL FUNCTIONS using the appliance TIME DELAY Time delay selection button A delay of up to 24 hours can be selected. Cancelling the delay To cancel the delay you have to press the clock button successively. The delay will be cancelled when 24 hours have been reached and the button is pressed once more. If the programme is changed the delay is also cancelled. Select ADDITIONAL FUNCTIONS Additional function selection button depending on programmes. By pressing the button several times you can choose between several combinations of one, two and up to three additional functions at the same time depending on the programme selected. Button: Easy-iron ( ) This option prevents garments from creasing by means of carrying out a special programme with special turns to fluff out the garments after spin-drying and make them easier to iron. Button: Extra rinse ( ) Increases the level of the final rinse obtained in the clothes; suitable for large loads and garments belonging to people with sensitive skin. Button: Intensive wash ( ) This option, specially recommended for heavily soiled, stained clothes, achieves better results by extending the normal wash cycle. Select Select Important 83 If during the additional function selection, the programme is changed or the ON/OFF button is pressed, all the functions selected until then are cancelled. 6 STARTING UP AND SELECTION BLOCK FUNCTION using the appliance STARTING UP a Start/pause button a To start up the washing machine you have to press the start / pause button. The display will constantly show the minutes left until the wash is over. BLOCK FUNCTION Block function selection The various buttons can be blocked to prevent them from being pressed and affecting the selected wash programme and options. The block function should be activated after the wash programme has been selected together with all its options. Activating the block function a The block function is activated by pressing the start/pause button and holding it down for at least 3 seconds. Deactivating the block function b The block function is cancelled when the wash programme comes to an end. If you want to deactivate the block function before the end of the programme, you have to hold the start button down again for at least 3 seconds. After 3 seconds, the block function indicator will disappear from the display, and it will go into pause status. The ON/OFF button does not cancel the block function. a b 84 7 WASH PROGRAMME PHASES AND POWER CUTS using the appliance PROGRAMME PHASES When the programme is running you can see which phase it is at on the display, as well as how long there is to the end of the programme. The active phases will appear successively at the top of the display as the programme progresses. [. . . ] One of them is that the washing machine cannot be opened until it is certain that the drum is quite still. This is why the hatch cannot be opened for 2 minutes. Other indications The washing machine can detect other indications. When this happens a number of other indicators appear on the display: F05, F06. . . , F10. Check if the problem is repeated and in this case call the AUTHORISED SERVICE CENTRE. 90 washing machine eco-note When your appliance is of no further use, it should not be disposed of together with general domestic waste. [. . . ]