User manual FAGOR FSO 900X

[. . . ] 2 Front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Display modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Selection of tools and types of material to bend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Type of material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Disable Y 1 5 jog Semiauto Page: 16 - Operating Manual - FSO 900X 3. 2 MACHINE REFERENCE (HOME) SEARCH If machine parameter PAR14. 4 = 1, the home search is mandatory on one or both axes on power-up. Whenever any axis has been moved while the NC was turned off, the axis that has been moved must be homed. Parameter PAR14. 1 distinguishes the sequence depending on whether home switches or used or not. 3. 2. 1 SEQUENCE FOR AXES WITH MANDATORY HOME SEARCH ON POWER-UP On power-up, pressing activates the mode. If the axis has a home switch, this unit displays the word: "START". If it is the Y axis, make sure that the ram is at the top position touching the home switch. If the axis does not use home switches, usually on Y, it will indicate a value that corresponds with the value of PAR10. Actuate on the "BEND" foot switch until the ram reaches its final position. Measure the distance between the support sides of the punch and die and preset that value (Yref). A wrong value too different from the real one may cause uncontrolled movements of the axis. It displays the Y coordinate (Y = Yref - Hpunch - Hdie) compensating the height of the active tools. The led turns off. If on power-up, you wish to quit the home search mode without actually homing, press and key in the access (or quit) code: 719200. FSO 900X - Operating Manual - Page: 17 3. 2. 2 SEQUENCE FOR AXES WITHOUT MANDATORY HOME SEARCH In initial mode, press there are two choices: . to modify. . · · · It access the program block N0. Only some values of the parameters affecting the geometry of the bend may be modified: Die number (with different width). When pressing , if the corrector has been stored, it recalculates all the following blocks that have been programmed by indicating the ANGLE in order to adapt them the new parameters of the N0 block and it will confirm that each one of them with two beeps. Edit the data of the block using the procedures of the Editing mode described Editing P0007 N00 Select Tool - in section 4. 1. 2 and press . When modifying on the "Select axis" or "Attributes" screen, it may require pressing two or three times to accept the new value and assume it. The sequence ends with a blinking of the "#" symbol at the upper right hand of the screen and it is confirmed with two beeps. To learn how to insert a new block, see section 4. 2 To quit the Editing mode, press . - FSO 900X - Operating Manual - Page: 21 4. 1. 2 EDITING A NEW PROGRAM gives access to editing the header of the To edit a new program, pressing program (Block N00). Use the key to go from one page or one block to the next while validating the data just entered. Use the keys to select the page to be displayed; but only on the block being edited (it is not possible to go back to the previous block). After validating a block, it is not possible to go back to it in order to change a value in it. To do this, finish editing the whole program and then proceed as described in section 4. 1. 1. [. . . ] To access this mode: - Press F - Select the "Comm" option (communications) of the LCD display by means of the S e lect: < and press Send> and press . to send the data out to a PC or peripheral device to receive data from a PC or peripheral or select <Receive> and press device. means of the - Select the type of data to transmit Parameters, Program, and Materials by keys and press . Page: 32 - Operating Manual - FSO 900X 6. 2 PARAMETER TRANSMITTING FORMAT The format of the transmitted parameters are: For value parameters: P00 123. 123 For binary parameters: P00 10101010 For option parameters: P00 0 For axis parameters: P??X 123. 123 Y 123. 123 The number of decimals depends on the selected resolution. 6. 3 PROGRAM TRANSMITTING FORMAT The format is: P000 P0. M0 G0. 000 P999. 9 X Y R T H B D U Where: P0000 P0 - M0 G0. 000 P999. 9 XY R T H B D U Program number. [. . . ]