User manual FAGOR CNC 8025 T FEATURES

[. . . ] When working in diameters, the "I" value in the table is in diameters and the value to be assigned to parameter "I" in the G51 function must always be given in radius. The figure reads M02 ó M30 It should read: M02 or M30 TING MANUAL (REF. It should say: The CNC asks which is the source program number and which is the new program number, after keying each one of them, press [ENTER]. If the number of the source program does not exist, or there is already a program in memory with the same number as the new one or if there is not enough when copying the new program , the CNC will issue a message indicating the cause. ALLATION MANUAL (REF. [. . . ] It is now possible to enter the sign of the leadscrew backlash for each axis P620(1, 2, 3, 4) Independent axis movement execution It is now possible to work at Constant Surface Speed in JOG mode P619(8) Date: July 1992 Software Version: 4. 2 and newer MODIFIED MANUAL AND SECTION Installation Manual Section 3. 3. 10 FEATURE Synchronisation with independent axis P621(4) Date: July 1993 Software Version: 5. 1 and newer MODIFIED MANUAL AND SECTION Installation Manual Installation Manual Installation Manual Programming Manual Section 4. 8 Section 5. Section 3. 3. 5 Chapter 13 FEATURE Linear & Bell-shaped acc. /dec. P811 The subroutine associated with the tool is executed before the T function. If P10 <> 0, it runs a final roughing pass before the finishing pass When having only one spindle range, if G96 is executed without any range being selected, the CNC will automatically select it. 8030 CNC with VGA Monitor Date: March1995 Programming Manual Chapter 6 Installation Manual Chapter 1 Software Version: 5. 3 and newer MODIFIED MANUAL AND SECTION Installation Manual Installation Manual Installation Manual PLCI Manual Sections 4. 7 & 6. 5. Section 3. 3. 10 Section 3. 3. 3 FEATURE Management of semi-absolute feedback devices (with coded Io) Spindle inhibit by PLC Handwheel managed by PLC Simulation of the "rapid JOG" key from PLC Initialization of machine parameters in case of memory loss. INTRODUCTION Introduction - 1 SAFETY CONDITIONS Read the following safety measures in order to prevent damage to personnel, to this product and to those products connected to it. This unit must only be repaired by personnel authorized by Fagor Automation. Fagor Automation shall not be held responsible for any physical or material damage derived from the violation of these basic safety regulations. Precautions against personal damage Before powering the unit up, make sure that it is connected to ground In order to avoid electrical discharges, make sure that all the grounding connections are properly made. Do not work in humid environments In order to avoid electrical discharges, always work under 90% of relative humidity (non-condensing) and 45º C (113º F). Do not work in explosive environments In order to avoid risks, damage, do not work in explosive environments. Precautions against product damage Working environment This unit is ready to be used in Industrial Environments complying with the directives and regulations effective in the European Community Fagor Automation shall not be held responsible for any damage suffered or caused when installed in other environments (residential or homes). Install the unit in the right place It is recommended, whenever possible, to instal the CNC away from coolants, chemical product, blows, etc. This unit complies with the European directives on electromagnetic compatibility. Nevertheless, it is recommended to keep it away from sources of electromagnetic disturbance such as. - Powerful loads connected to the same AC power line as this equipment. - Nearby portable transmitters (Radio-telephones, Ham radio transmitters). - Nearby arc welding machines - Nearby High Voltage power lines - Etc. Ambient conditions The working temperature must be between +5° C and +45° C (41ºF and 113º F) The storage temperature must be between -25° C and 70° C. (-13º F and 158º F) Introduction - 3 Protections of the unit itself Central Unit It carries two fast fuses of 3. 15 Amp. / 250V. All the digital inputs and outputs are protected by an external fast fuse (F) of 3. 15 Amp. / 250V. See the identification label of the unit. Precautions during repair Do not manipulate the inside of the unit Only personnel authorized by Fagor Automation may manipulate the inside of this unit. Before manipulating the connectors (inputs/outputs, feedback, etc. ) make sure that the unit is not connected to AC power. Safety symbols Symbols which may appear on the manual WARNING. symbol It has an associated text indicating those actions or operations may hurt people or damage products. [. . . ] This error comes up when it is mandatory to search home on all axes after power-up. The CNC initializes the RS232C serial line parameters: P0=9600, P1=8, P2=0, P3=1, P605(5)=1, P605(6)=1, P605(7)=1. 095 ** Parity error in general parameters. The CNC initializes the RS232C serial line parameters: P0=9600, P1=8, P2=0, P3=1, P605(5)=1, P605(6)=1, P605(7)=1. The CNC initializes the RS232C serial line parameters: P0=9600, P1=8, P2=0, P3=1, P605(5)=1, P605(6)=1, P605(7)=1. [. . . ]