User manual FAGOR 8040 M CNC

[. . . ] 2 Keyboard customizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATING IN JOG MODE 2. 1 2. 2 2. 2. 1 2. 2. 2 2. 2. 3 2. 3 2. 4 2. 4. 1 2. 4. 2 2. 4. 3 2. 4. 4 2. 4. 4. 1 2. 4. 4. 2 2. 4. 4. 3 2. 5 2. 5. 1 2. 5. 2 2. 5. 3 2. 6 2. 6. 1 2. 6. 2 2. 6. 2. 1 2. 7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Axis Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Work Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The spindle revolutions therefore depend on the position taken by the tool tip with respect to the turning axis. If the tool tip moves away from the turning axis, the spindle revolutions thus go down, and if it gets closer, they go up. When Constant Surface Speed is selected the CNC displays the following information. 1. - Actual spindle speed in rpm. To select any other speed press value The CNC assumes this value and if the spindle is started it will update the actual speed of the spindle (in rpm. ) turning clockwise, 3. - State of the spindle: To modify the status of the spindle press: turning counterclockwise or stopped. 4. - % of the theoretical Constant Surface Speed being applied. To modify this percentage (%) press : 5. - Maximum spindle speed in rpm. To select any other speed press Enter the new value and press 6. - Spindle range currently selected. and then use the key to frame the twice and the CNC will frame the present value. The CNC will assume this value. Enter the range number to be selected and press or Note: When the machine does not have spindle ranges this message is superfluous. For this reason, when text 28 of program 999997 is not defined, the CNC does not display this message. Chapter 2 - page 20 MCO-TCO work mode 2. 6. 2. 1 OPERATING AT CONSTANT SURFACE SPEED (CSS) When Constant Surface Speed operating mode is selected (CSS), the CNC assumes the spindle range selected at present. In this operating mode, when a new constant surface speed is selected, the following cases may arise: a) The spindle is stopped The CNC selects the new speed but does not apply this until the spindle moves. b) The spindle is started The CNC, depending on the position of the axis, calculates and makes the spindle turn at the corresponding rpm. Screens 001 through 200 may also be used for diagnosis, setup, to inform of CNC, PLC or Drive status, etc. They are defined in the same way as the canned cycles, they have a configuration file an a routine associated with them and the texts they use must be defined in program P999995. Warning The text for the screen title should be defined with the same number in the WGDRAW application as that of the screen. This way, when pressing the CNC will show the number and title (text of program P999995 of the same number) of the available screens. Chapter 3 - page 2 MCO-TCO work mode 3. 1 ASSOCIATED PROGRAMS In CO mode, programs P900000 through P999999 are reserved for the CNC itself and cannot be used as user part-programs. Some have a special meaning and must be defined by the machine manufacturer. P999001 through P999200 Configuration files defined by the manufacturer. P999001 for cycle 1, P999002 for cycle 2 and so on up to 999200 which is for cycle 200. P999500 Program which logs the errors occurred when interpreting a configuration file. P994xxx When the OEM cycles allow to define profiles, the operator defines them with 3 digits (0 through 999) and the CNC stores them internally as P994xxx. The rest of the programs reserved are for internal CNC use and MUST NOT be deleted. 3. 2 ASSOCIATED ROUTINES In CO mode, routines 0000 through 8999 are free and 9000 through 9999 are reserved to customize the CNC. It is recommended to define all the OEM routines in a program with a high number in order to prevent the operator from modifying them. [. . . ] to execute an operation or part-program, the CNC displays the standard screen TCO Model If you press MCO model the CNC displays the special screen for the CO mode. After selection, the operation or part can be executed as many times as necessary. To do this, after execution once more press During execution of the operation or part one can press To stop execution press After stopping the execution the CNC allows a tool inspection to be made. to access the graphics mode. Chaper 5 - page 4 MCO-TCO work mode 5. 4. 1 TOOL INSPECTION Depending on how the TOOLINSP mark has been set at the PLC, the tool inspection mode will be available after interrupting the execution without pressing any key or after pressing Once tool inspection has been selected, one can: Jog the axes up to the tool change position Move the tool to the tool change position by means of the keys or the handwheels. Select another tool In order to make the tool change, the standard screen for the CO mode must be selected. [. . . ]