User manual FAGOR 6CFI-4GLSB

[. . . ] The hob should be connected to the gas system only by a properly certified fitter of gas appliances, which should be confirmed on the product's warranty card. the lack of such confirmation will render the warranty null and void!Prior to installation, ensure that the type of gas your are supplied with is compatible with the type of gas the hob is adjusted to. information about the required type of gas is stated on the rating plate of the appliance. [. . . ] 4 and 5) After affixing the gasket place the hob in the cavity in the worktop 1 and press down tightly so that sealing joint is perfectly closed 6. Fix the hob underneath to the worktop 1 with clamps 3 and screws 4 supplied in the accessory bag 7. 6) should be installed under the worktop to protect the user from accidentally touching the hot hob from beneath. The connection of the hob to the gas supply system should be made in accordance with the regulations in force. All activities involved in connecting the hob to the gas supply system, adjusting the taps and replacing nozzles should only be performed by a properly certified person 3. Before beginning the connection operation make sure that the gas valve is closed!Gas supply system should be connected to the pipe with appropriate fittings. CONNECTING THE HOB TO NATURAL GAS SUPPLY When connecting the hob to natural gas supply use an elbow with gasket and seal the taper thread (at the outlet) with Teflon band. The hob may be connected to the internal supply system with a rigid connection or a flexible metal tube. 7 CONNECTING THE HOB TO AN LPG CYLINDER Do not install the appliance in the basement or in any other room whose floor is below the ground level as LPG is heavier than air and accumulates at the floor level. The cylinder should be located in an easily accessible place, positioned vertically and secured against falling over. To connect the appliance use the LPG tip with a gasket as shown in fig. Each time after connecting the hob to LPG cylinder check the soundness on high pressure side, check the cylinder valve for soundness and the connection of regulator with the cylinder and its operation. The soundness of all connections and the cylinder valve maybe pre-checked by applying soap solution on the said points with the normal working pres-sure. Under no circumstances can the gas soundness be checked by means of a naked flame (e. Regularly, every six months, check the condition of the tube and soundness of its connection to the end elements. Before beginning these activities you must: ­ shut down the cock shutting off the gas supply system or cylinder from the hob, -shut down all the taps in the hob, ­ disconnect the hob from the mains. Then: ­ remove the burners' lids and rings, ­ remove the nozzles with socket wrench no. 7 and replace them with new ones in accordance with table2, ­ put burners' rings and lids back, ­ adjust the taps and check the connections for soundness Then: ­ open the gas flow with a knob and light the adjusted burner, . And then, without changing that position, ­ set the knob in the simmering position remove it from the tap's mandrel ­ put a screwdriver in opening 'A" or mandrel opening "B" (depending on the type of the tap fig. 10) and turn it, observing the flame, to achieve such a size of the flame that will prevent it from being extinguished in a slight draught or during the operation of quick switching from the full to the simmering position . Of the flame and back; the adjustment is correct when the core of the flame is cone-shaped in green and blue colour and is ca. [. . . ] In the warranty period all repairs except for the ones specified below should be carried out by the authorised Servicing Point. After the warranty period ends the user should request the servicing point to conduct periodical inspections of the appliance. Table 3 Symptoms Cause What to do - Close burners' taps - Close the shut-off valve on the system, before the hob - Air the room - Remove the elements of the burner, clean them and clear the burner ports - Assembly the burner correctly and try to light it again - Remove all the elements of the burner - Clean the nozzle and, if necessary, use a thin copper wire (do not use steel wire or drill the hole ) Not clear burner ports The burner does not light Blocked (flooded ) nozzle The igniter does A break in the electric system not light the burner (no Dirty burners and/or spark) ignitors - clean and dry the burners and ignitors thoroughly If after the above-specified steps have been taken the appliance still does not work properly, contact the nearest authorised servicing company. A faulty gas hob should not be used until it is repaired by qualified servicing personnel. [. . . ]