User manual FABER PRETTY ISOLA ACT EG8 X A90

[. . . ] Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.  If the extractor is used in conjunction with non-electrical appliances (e. Gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. [. . . ] For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert For wooden beam ceilings, drill according to the wood screws used. For the air outlet (Ducted Version), drill according to the diameter of the external air ex- Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling: ?For concrete ceilings, use the appropriate plugs for the screw size (not provided). For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided. Should it be necessary to adjust the height of the frame, proceed as follows: · Unfasten the metric screws joining the two Opposite parts that can be seen from the front; · Adjust the height of the frame as required, then replace the screws removed as above, making sure that you insert 2 of them close to the panel lock; · Lift the frame, insert the slots onto the screws and slide them until they lock; · Tighten the two screws and insert the other two screws provided. 2, remove the film from the double sided adhesive and fix it inside the frame so as to hold it more firmly. Before final locking of the screws it is possible to make small adjustments to the frame, making sure that the screws do not come out of the adjustment slot. The Frame must be securely fastened both Due to the weight of the Hood and the stress caused by occasional sideways pressure on the Appliance when in position. When fastened, check that the base is stable even when the Frame is subjected to bending. In all cases where the Ceiling is not sufficiently strong at the point of suspension, the Installation technician must strengthen it with suitable plates and counterplates, anchored to structurally sound elements. When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. Apply the Novastick tape 16 to the front edge of the Upper Chimney from the top part down to the start of the Lower Chimney. From inside the Hood canopy, screw the Motor unit 3 to the Hood canopy 1 using 6 Screws 12f provided. Make the electrical connections between The Motor Unit 3 and the Hood Canopy 1, Connecting the Controls connector and the Warning: Make sure that the Connectors Are properly inserted into the housing. Fitting the Panel and Fixing the Hood Canopy Before fixing the Hood Canopy to the Frame: · Remove the Grease filters from the Hood Canopy; · Working from below, fix the Hood canopy to the Screw on the SILK fixing bracket 7. 4 using the 4 screws provided; 2 screws are used to fix the bracket to the motor unit 4 and the other 2 are used to fix the bracket to the bearing chimney 2. Then hook the upper part of the Panel 3, adjusted to size, to the rubber supports in the upper part and in the lower part of the Frame. Slide the lower part of the Panel 3 until its metal tabs slot into the slots in the frame; Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. According to the type of Hood Commands, press and hold button or for 5 seconds, - In the former case the Display will show the letters An followed by CA; - In the latter case an animation will be displayed. Calibration of the system takes 40 seconds, during which "noises" will be heard. [. . . ] With all the loads turned off (Motor and Lights), to turn IR+Dot (Flashes once)-Alarm Deactivated. H Turns the lighting system on and off in Courtesy Light Press and hold the button for 5 seconds to Disable / En- Displays An and then dS ­ "Active Noise" system REMOTE CONTROL (OPTIONAL) This appliance can be commanded using a remote control, powered by a CR2032 type 3 V battery (not supplied). Do not discard the batteries with normal waste, they must be Put into the specific containers. metal grease filters They can be washed in the dishwasher, and need to be cleaned whenever the FG sign appears on the display or at least once every 2 months use, or more frequently if use is particularly intensive. [. . . ]