User manual EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER. We hope that this EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER user guide will be useful to you.
Manual abstract: user guide EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER
Detailed instructions for use are in the User's Guide.
[. . . ] MEASUREMENT
4. 1 4. 2 4. 3 4. 4 4. 5 Taking Measurements Displaying Maximum and Minimum Readings Holding a Reading Releasing a Held Reading Maximum and Minimum Hold Mode 10 10 10 11 11
10
5. RETURN OF ITEMS
12 13 13 14 15 16 17
Instruction Manual
Temp 4/5/6
1. INTRODUCTION
1. 1 Introducing the economy series
Thank you for purchasing the Temp 4/5/6 meter. These microprocessor-based handheld meters are economical and easy to use. [. . . ] The Temp 4/5/6 meters allow you to have a 1-point calibration as fine adjustment by changing its offset value. This is useful if you replace the probe and should recalibrate the probe to the meter. Press ON/OFF key to power up the meter and wait for meter to enter measurement mode. Dip the probe in a constant temperature bath, or in liquid whose temperature can be checked with an accurate thermometer. For best accuracy, place the probe and thermometer in a constant temperature bath. To enter temperature calibration mode, press and hold CAL key for 5 seconds before release. Press MAX/ or MIN/ key to adjust the displayed value until it matches the correct temperature. NOTE: The maximum adjustments allowed are ±5 °C from factory default.
7
Instruction Manual
Temp 4/5/6
6. The LCD displays "CO" momentarily, and the meter then reverts to measurement mode. See figure below.
Press down CAL key for 5 seconds before release
°C
CAL
°C
From measurement mode
°C
HOLD ENTER
°C
8
Instruction Manual
Temp 4/5/6
3. 1. 2 Temperature Curve Selection (Temp 5 Meter Only) In the event temperature probe has drifted too far from its original characteristic due to age and use or if the probe is being replaced, it may be a good idea to match probe to the best curve. Dip the probe in a constant temperature bath or a liquid whose temperature can be checked with a thermometer known to be accurate. For best accuracy, place the probe and thermometer in a constant temperature bath. Press the C/ F key again to scroll through three temperature curves (low, mid. Choose the curve which gives you a reading closest to the actual value (of the bath or thermometer). The unit will display "CO" and revert to the temperature calibration mode, with the display still flashing. Press and key to make fine adjustment until the display shows the correct desired temperature. The and key will scroll to the maximum o allowable value (maximum adjustment is ±5 C from factory default). The LCD displays "CO" momentarily, and the meter then reverts to measurement mode.
o o o o
2.
3.
4.
5.
6.
.
9
Instruction Manual
Temp 4/5/6
4. o o The C or F annunciator displays in your LCD to indicate which mode you are taking measurements in. Press the C/ F key to toggle between each measurement mode.
o o
4. 2 Displaying Maximum and Minimum Readings
The EcoScan Temp meter can momentarily display the maximum and minimum temperature measured since you switched the meter on. The "MAX" or "MIN" annunciator displays in the LCD and the maximum or minimum temperature momentarily displays. Meter then returns to measurement mode.
MAX
.
4. 3 Holding a Reading
HO
°C
To freeze or hold your reading, press HOLD key once. [. . . ] Eutech Instruments/ Oakton Instruments will determine if the product problem is due to deviations or customer misuse. Out of warranty products will be repaired on a charged basis.
Exclusions The warranty on your instrument shall not apply to defects resulting from: · · · Improper or inadequate maintenance by customer Unauthorised modification or misuse Operation outside of the environment specifications of the products
16
Instruction Manual
Temp 4/5/6
11. RETURN OF ITEMS
Authorisation must be obtained from our Customer Service Department or authorised distributor before returning items for any reason. A "Return Goods Authorisation" (RGA) form is available through our authorised distributor. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER will begin.