User manual EUTECH INSTRUMENTS CYBERSCAN PH 110 PHMVRS232 METER

[. . . ] Instruction Manual pH 11 & pH 110 Hand-held pH / mV / Temperature / RS 232 Meter 68X361301 Technology Made Easy . . . Rev. 2 - 11/03 Preface This manual serves to explain the use of the hand-held series meters. The manual functions in two ways, firstly as a step by step guide to help the user operate the meter. This instruction manual is written to cover as many anticipated applications of the pH meters as possible. [. . . ] The ATC indicator appears in the lower right-hand corner to indicator Automatic Temperature Compensation (section 5. 2 on Manual Temperature Compensation). Dip the probe into the sample. 3. When dipping the probe into the sample, the sensor or the glass bulb of the electrode must be completely immersed into the sample. To toggle between pH and mV (or Rel mV) readings, press the MODE key. 5. 3. 1 Taking measurements with READY indicator selected on If the READY indicator has been activated, the READY annunciator lights when the reading is stable2 *. 5. 3. 2 Taking measurements with the AUTO HOLD feature selected on This feature is available on model pH 110 only. When a reading is stable for more than 5 seconds, the AUTO HOLD feature will automatically "HOLD" the reading. The "HOLD" indicator appears on the left side of the display. Switch the Auto Hold feature on or off in SETUP program in section 9. 2. 1 - P1. 1: READY Indicator and Auto Hold function on page 34. 2 The READY indicator appears and the reading holds until the measured value exceeds the tolerance (±0. 02 pH; ±0. 2 mV <400; ±2 mV > 400). 19 Instruction Manual CyberScan pH 11 / 110 6 HOLD FUNCTION This feature lets you freeze the value of the pH, mV (or relative mV) and temperature readings for a delayed observation. To hold a measurement, press the HOLD/ENTER key while in measurement mode. 07 pH °C ATC Figure 18: Press HOLD to freeze reading NOTE: a. This meter shuts off automatically 20 minutes after last key is pressed. If the meter is shut off either automatically or manually, the HOLD value will be lost. When this feature is switched on, the display will automatically "HOLD" a reading that has been stable for more than 5 seconds. When "HOLD" indicator appears, press the HOLD/ENTER key to release the reading. To switch on or off the Auto Hold feature, see section 9. 2. 1 P1. 1: READY Indicator and Auto Hold function on page 34. 20 Instruction Manual CyberScan pH 11 / 110 7 MEMORY FUNCTION The memory function is available in both pH 11 and pH 110 meters. These meters store data in sets: READY MEAS · · · pH and temperature mV and temperature Relative mV and temperature (for pH 110) MI 8. 23 2. 13 pH °C ATC The pH 11 meter can store up to 50 sets of data while pH 110 meter can store up to 100 sets of data. For example, you can store 17 pH and 19 mV values. MEM MEM 7. 1 1. Memory Input During any measurement function (MEAS), press MI/ key to input any data into the memory. If the memory is full, the display will flash "MEM ­ FUL" momentarily (Figure 20). The first value stored will be erased to create space for the new value. MEM 1 2. 24 MI pH °C ATC FUL MEM MEM MEM 2 Figure 19: Data storage in memory MEM MEM 1 Figure 20: Memory full 21 Instruction Manual CyberScan pH 11 / 110 7. 2 Memory Recall MEAS This function recalls the previous readings stored in the memory. The memory location screen ­ MEM, "Loc" and the memory number ­ will flash on the display. [. . . ] Combination ORP electrode, epoxy-body, single-junction, 12x110 mm, 1-m cable length Combination ORP electrode, epoxy-body, double-junction, 12x110 mm, 1-m cable length RS232 Communication Cable: 9-pin male to 9-pin female connector, 1m cable length Serial Impact Micro-Printer: Dot-matrix, paper-roll portable printer with 25-pin female connector, with a roll of paper and 110/120 VAC power adapter provided Serial Impact Micro-Printer: Dot-matrix, paper-roll portable printer with 25-pin female connector, with a roll of paper and 220/230 VAC power adapter provided pH Carrying Kit Set - Plastic Carrying Case comprises 1 x pH 4. 01, pH 7. 00, pH 10. 01 buffer solutions (60 ml) and 1 x empty rinse water bottle (480 ml) 110/120 VAC Power Adapter (50/60 Hz) 2-flat pin US type, 9 VDC 500mA (for standard portable meters) 220/230 VAC Power Adapter (50/60 Hz) 2-round pin Euro type, 9 VDC 500mA (for standard portable meters) Eutech Instruments Order Code EC-PH11/01 EC-PH110/01 EC-PH11/02K EC-PH110/02K EC-PH5-TEM01P 15X000700 EC-FC72521-01B EC-FC72522-01B EC-FC73528-01B EC-FC79601-01B EC-FC79602-01B EC-CA01M09F09 ECMIC ROPRNTR01 EC-MICROPRNTR02 EC-PH-WPKIT EC-120-ADA EC-220-ADA 65 Instruction Manual CyberScan pH 11 / 110 15. 2 Oakton Instruments Item CyberScan pH 11 Portable pH/mV Meter with 2 electrode holders 15X000700, temperature probe EC-PH5-TEM01P CyberScan pH 11 Portable pH/mV Meter with pH electrode EC-FC7252201B, 2 electrode holders 15X000700, temperature probe EC-PH5-TEM01P & pH carrying kit set EC-PHWP-KIT CyberScan pH 110 Portable pH/mV/RS232 Meter with 2 electrode holders 15X000700, PC-based DAS, RS232C cable & temperature probe EC-PH5TEM01P CyberScan pH 110 Portable pH/mV/RS232 Meter with pH electrode ECFC72522-01B, 2 electrode holders 15X000700, temperature probe EC-PH5TEM01P, PC-based DAS, RS232C cable & pH carrying kit set EC-PHWPKIT Temperature probe for pH 11 and pH 110 meters. Electrode Holder for probes and electrodes (12 mm diameter) General purpose epoxy-body pH combination electrode, single-junction, 12x110 mm, 1-m cable length. General purpose epoxy-body pH combination electrode, double-junction, 12x110 mm, 1-m cable length. "All-in-1" pH/Temperature (ATC) combination epoxy-body electrode, singlejunction, 12x110 mm, 1-m cable length. [. . . ]