User manual EINHELL EBH 750

[. . . ] Cables, plugs and socket couplers must meet the following requirements listed below. Power cables used to connect machines must have a rubber insulation sheath. The power cables must, at the very minimum, be of type HO5RN-F and 3-stranded. Plugs and socket couplers for the power cables must be made from rubber and splash-proof. [. . . ] maintain a solid footing and wear sturdy , non-slip footwear and long trousers. Use special caution when backing up and pulling the machine (tripping hazard). Maintenance and cleaning work on the machine as well as removal of the safety devices may only be performed when the motor is switched off and the power cable has been pulled. Worn out or damaged hoe blades should only be replaced by an authorized professional (see address on warranty certificate). Do not clean the tool with running water - and particularly not with a pressure hose. ) are always tightened so that the machine can be safely operated at all times. All the metal parts should be cleaned and then oil to ensure that they provide a long life. For best results, clean the plastic parts of the machine with a brush or rag. At the end of the season, perform a general inspection of the machine and remove any deposits which may have accumulated. Place the machine in front of the area you wish to hoe and hold it securely on the push bar before you switch on the machine. To achieve cleanly hoed soil always ensure that you guide the machine in straight lines wherever possible. Insodoing, the aeration swaths should always overlap each other by a few centimeters in order to avoid bare strips. Switch off the motor promptly when you arrive at the 12 Season, ensure that you check the condition of the machine. If repairs are necessary, please contact one of our customer service centers (see address on warranty certificate). Voltage Power input Working width Hoe diameter Idle speed Number of blades LPA noise level LWA peak noise level Vibration at the handlebars ahv 230V ~ 50Hz 750 W 30 cm 22 cm 400 rpm 4 pieces 70 dB(A) 93 dB(A) 2. For safety reasons, we recommend having the hoe blades replaced by an authorized professional (see address on warranty certificate). Use only genuine spare parts since otherwise the function and safety of the machine cannot be guaranteed. Please quote the following data when ordering replacement parts: Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required For our latest prices and information please go to www. Fault Motor does not start Possible causes a) No power at the plug b) Cable defective c) Switch/plug block defective d) Motor terminals or capacitor disconnected e) excessive working depth a) Soil too hard b) Blades badly worn Remedy a) Check the power cable and fuse b) Check c) By customer service workshop d) By customer service workshop e) Reduce working depth a) Correct working depth b) Replace hoe blades For protection, the motor is equipped with a thermal switch which cuts out when the motor is overloaded and switches on again automatically after a short cooling period. K t p erklärt folgende Konformität gemäß EU-Richtlinie und Normen für Artikel declares conformity with the EU Directive and standards marked below for the article déclare la conformité suivante selon la directive CE et les normes concernant larticle verklaart de volgende conformiteit in overeenstemming met de EU-richtlijn en normen voor het artikel declara la siguiente conformidad a tenor de la directiva y normas de la UE para el artículo declara a seguinte conformidade de acordo com a directiva CE e normas para o artigo förklarar följande överensstämmelse enl. The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH. T For EU countries only Never place any electric tools in your household refuse. [. . . ] The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase. [. . . ]