User manual EINHELL BT-RO 1200 E

[. . . ] Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 1 Bedienungsanleitung Elektro-Oberfräse t p C Operating Instructions Electric Router Mode demploi Défonceuse électrique Istruzioni per luso Fresatrice verticale elettrica lL Betjeningsvejledning Elektrisk overfræser A Használati utasítás Villamos -felsmaró Bf Upute za uporabu Elektricna glodalica za izradu utora 4 j W Uputstva za upotrebu Elektricna glodalica za izradu utora Návod k obsluze Elektrická horní frézka Návod na obsluhu Elektrická horná frézka Art. -Nr. : 43. 504. 80 I. -Nr. : 01017 BT-RO 1200 E Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 2 1a 6 7 8 5 7 4 9 10 3 2 1 1b 19 11 1c 22 18 17 20 16 12 3 23 13 21 14 15 2 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 3 2 3 1 1B 1A f 2 4 5 3 3 b a 2 b a 21 b a 2 3 c 13 6 20 7 c 20 f 2 d e b 3 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 4 8 12 9 23 10 10 12 11 12 22 10 12 13 15 9 14 4 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:32 Uhr Seite 5 14 19 15 18 17 16 15 14 16 5 17 11 + -- 4 18 19 a c b c 5 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:33 Uhr Seite 13 GB Important!When using equipment, a few safety precautions must be observed to avoid injuries and damage. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, give them these operating instructions as well. [. . . ] Set the depth stop (19) to the required routing depth using the scale and secure it with the wing screw (16). 6. 4 Routing To avoid damage to the router, make sure there are no foreign objects attached to the workpiece. Select the speed as described in point 6. 2 and switch the machine on (see point 6. 1). Only then should you lower the router to its working height and lock the machine with the locking grip (9). To avoid accidents you must always cut against the direction in which the tool turns (Fig. Feed speed: It is very important to machine the workpiece at the correct feed speed. We recommend that before you machine the actual workpiece, you carry out several trial cuts on a waste piece of the same type. This will enable you to find the best working speed for the workpiece very easily. If you are cutting inflammable material such as wood, the workpiece could ignite. 6. Secure the workpiece so that it cannot be thrown through the air as you work on it. 16/Item 4) Press the safety lock-off (5) and then press the ON/OFF switch (4) to switch on the machine. 17 ­ Item 11) The best speed depends on the material and the diameter of the cutter. Select a speed between 11, 000 and 30, 000 rpm using the speed control switch (11). The speeds in the various switch positions are as follows: Switch position 1: approx. 26, 000 rpm 15 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:33 Uhr Seite 16 GB Feed speed too high: The cutter could be damaged. Allow the cutter to come to a complete standstill before removing the workpiece or putting down the router. 6. 5 Routing in stages Depending on the hardness of the material you wish to cut and the cutting depth, it may be a good idea to proceed in stages. If you wish to route in several stages, turn the end stop revolver (14) after you have set the cutting depth as described in point 6. 3 so that the depth stop (19) is over the highest end stop (15). After completing the first routing operation, adjust the end stop revolver (14) so that the depth stop (19) is above middle end stop (15). 6. 6 Routing circles with the compass point (13) Proceed as follows to route circles around a centre point: Fit and adjust the compass point (13) as described in point 5. 3. Place the compass point (13) on the centre point of the circle you wish to route and apply pressure to it. 8. 3 Maintenance There are no parts inside the equipment which require additional maintenance. 16 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:33 Uhr Seite 17 GB 8. 4 Ordering replacement parts Please quote the following data when ordering replacement parts: Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required For our latest prices and information please go to www. isc-gmbh. info 9. [. . . ] Ne sont pas concernés les accessoires et ressources fournies sans composants électroniques. 67 Anleitung BT-RO 1200 E_SPK1:_ 15. 09. 2008 15:33 Uhr Seite 74 t GUARANTEE CERTIFICATE Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the following terms under which guarantee claims can be made: 1. [. . . ]