User manual EINHELL BT-PL 750

[. . . ] Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes. 4. Technical data Mains voltage: Power input: Idling speed: Chip depth: Rebate depth: Plane width: Protection class: Weight: 230 V ~ 50 Hz 750 W 16, 500 min -1 0-2 mm 0-6 mm 82 mm II / ® 2. 9 kg 1. Safety information Please refer to the booklet included in delivery for the safety instructions. Any errors made in following the safety regulations and instructions may result in an electric shock, fire and/or serious injury. [. . . ] Width of step: You can set the width of the step with the parallel stop (13). 12 Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:06 Uhr Seite 13 GB Depth of step: We recommend you to set a cutting depth of 2 mm and to keep planing the workpiece until the required depth of step is reached. wrench (a) supplied and push the carbide metal reversible knife out of the planing shaft using a piece of wood. Check that the planing knife conforms with both ends of the planing shaft. Important: Before using the hand-held electric plane make sure the knives are installed securely and in the right place. 13) (8) Front base plate (moving plane shoe) (5) Rear base plate (fixed plane shoe) 1. Notches in the surface Problem: The cutting edge on the planing knife (or both planing knives) is not parallel to the height of the rear base plate. 7. Replacing the power cable If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its aftersales service or similarly trained personnel to avoid danger. 8. Cleaning, maintenance and ordering of spare parts Always pull out the mains power plug before starting any cleaning work. 8. 1 Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. We recommend that you clean the device immediately each time you have finished using it. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. 8. 2 Carbon brushes In case of excessive sparking, have the carbon brushes checked only by a qualified electrician. The carbon brushes should not be rep laced by anyone but a qualified electrician. 12-13) Important: Always pull the plug out of the power socket before doing any work on the equipment. The hand-held electric plane comes with two carbide metal reversible knives. The guide slot on the reversible knives ensures the same height setting after a change. Furrows at the start of the planed surface Problem: The cutting edge on the planing knife (or both planing knives) is below the height of the rear base plate. Furrows at the end of the planed surface Problem: The cutting edge on the planing knife (or both planing knives) is above the height of the rear base plate. Place the new drive belt on the small belt pulley (c) and pull the belt onto the large belt pulley (d) whilst turning the planing shaft. Ensure that the longitudinal grooves on the drive belt are in the guide grooves on the drive wheels. 8. 5 Maintenance There are no parts inside the equipment which require additional maintenance. 13 Anleitung_BT_PL_750_SPK1:_ 15. 09. 2008 15:06 Uhr Seite 14 GB 8. 6 Ordering replacement parts Please quote the following data when ordering replacement parts: Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required For our latest prices and information please go to www. isc-gmbh. info 9. [. . . ] The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase. [. . . ]