User manual DSC POWER 608 V2.3

[. . . ] ·WARNING· This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. Instruction Manual Software Version 2. 3 WARNING Please Read Carefully Note to Installers This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. System Failures This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. [. . . ] To program a new code: Enter [D][5][Master Code][code number 01 to 32][new access code]. Access codes must be four digits unless otherwise indicated by your installer. If an access code already exists for the code number you have selected, it will be replaced by the new code. Be sure to record your new code(s) on the "System Information" page in this book. The Master code cannot be erased. 7 PC5508Z LED Keypad Memory Light Upon disarming, if an alarm has occurred while the system was armed, the Memory light will turn ON (See "Disarming the System" on page 6). Bypass Light If the Bypass light is ON, one or more zones are bypassed (See "Zone Bypassing" on page 11). Fire Light If the Fire light is ON, a fire alarm has occurred (See "Fire Alarm Operation" on page 14). Program Light The Program light will flash when you are programming access codes, or performing other programming functions. If someone is programming at another keypad, the Program light will turn ON to indicate that the system is busy. LCD5500Z Keypad The Liquid Crystal Display (LCD) displays prompts and system information on two 16 character lines. If "< >" appears, more information can be accessed by using the arrow (< >) keys. Press [>] to advance the display to next function or item of information. Press the keys on the number pad as prompted by the LCD display to view alarms or troubles, to arm and disarm the system and to bypass zones. To select a function press [D]. Display Lights (All Keypads) PC5516(Z) LED Keypad PC5532(Z) LED Keypad Ready Light If the Ready light is ON, the system is ready for arming. The system cannot be armed unless the Ready light is ON (see "Arming the System" on page 4). Armed Light If the Armed light is ON, the system has been armed successfully. Trouble or System Light If the Trouble light is ON, see "Viewing Trouble Conditions" on page 11. Emergency Keys (All Keypads) Press both * Keys for two seconds to send a FIRE transmission. * IMPORTANT NOTE (All Keypads): The Fire, Auxiliary and Panic keys will NOT function unless programmed by the installer. If these keys are in service and the installer has enabled audible feedback, holding down the key for two seconds will cause the keypad sounder to beep indicating that the input has been accepted and transmission is underway. The PC5516, PC5516Z, PC5532 and PC5532Z Keypads are available for applications with more than 8 zones. The functions explained in this manual are the same for all three LED keypad types. Important Note: Test system weekly and have any system trouble conditions corrected by your alarm installer. 8 9 Programming codes from an LCD Keypad: Master Code Press the [D] key to enter the function list. Access Codes Enter Master Access Code Enter your current Master Code. The display will read. . . (*) to Edit <> "40P" represents the Master Code. Press the [D] key to indicate that you wish to User Code 40P program the Master Code. [. . . ] To be certain of the number of devices that you may connect to your line, you may want to contact your local telephone company. EQUIPMENT MAINTENANCE FACILITY If you experience trouble with this telephone equipment, please contact the facility indicated below for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. 160 Washburn St. , Lockport, NY 14094 16 LIMITED WARRANTY Digital Security Controls Ltd. [. . . ]