User manual DSC PC2000

[. . . ] 4 IMPORTANT NOTICE Digital Security Controls Ltd recommends that you read this manual carefully and become familiar with the operation of your security system. Check with the installing company to see which commands listed in this manual apply to your particular security system. Fill out the system reference sheet and store this booklet in a secure place for future reference. To do this, first inform the monitoring station that you are testing your system. [. . . ] If one of these conditions occurs, the keypad `TROUBLE' indicator will light. I- DEFECTIVE STANDBY BATTERY 2- AC POWER FAILURE 3- BLOWN FUSE IN CONTROL PANEL 4- TELEPHONE LINE PROBLEM 5- UNSUCCESSFUL COMMUNICATION ATTEMPT WITH MONITORING STATION 6- not used 7- BELL/SIREN CIRCUIT DEFECTIVE 8- MEMORY LOSS (USE MASTER CODE TO REPROGRAM) Press the [#] to return to `READY'. ALARM MEMORY DISPLAY If the `MEMORY' light is on an alarm has occured. Press [#] to return to `READY'. . ARMED light will come on indicating system armed. Ensure READY light on, enter 4 digit code. MEMORY light on means an alarm has occurred To display zone that caused alarm, press @I then &I. Zone light will come on indicating which zone caused alarm. ZONE light(s) when on in the normal operating mode indicate an open zone. Refer to zone chart on keypad door for detailed zone information. Ready tliht must be on. ' KS SYWEht FltEQtJE~y SHUNT light will come 1 on when you by-pass a zone. To by-pass a zone, press 63 then ci3 and then the zone(s) you wish to by-pass. r c I Program TROUBLE light on means there is a fault on the system. Select which code you wish to program 1 thru 8, then enter 4 digit code. Program light must be "on" to add or change user codes. Key pad door has zone identification and basic user instructions. Protects keypad when keypad not in use. ALARM TEST Press I*] lhen [4] for a 4 second lest of the keypad lights, keypad sounder and sirens. A lest transmission to the monitoring station is not done with this command. PROGRAMMING ADDITIONAL SECURITY CODES Enter [*I&] and [master security code]. The `PROGRAM' light will flash and the `ZONE' lights will show which codes have already been programmed (up to 8 codes can be programmed from the keypad). Press any key from (1 to 81 to indicate which one of the 8 codes is being programmed. The `ZONE' light will flash to indicate which code is being programmed. At this point if [ * JC * xc] instead of a [4 digit code] is entered, any previously programmed code in this localion will be eliminated. To review: programming a new code; enter [*]$$[master code], (l to 8], [4 digit code]. eliminating an existing code; enter [*], [5]. [master code]. [l to S], [xx-x-x] Press [#] to return to `READY'. SETTING AUTOMATIC ARMING TIME The PC2000 can be programmed to automatically arm each day at the same lime. Then enter any [two digits] (from 01 to 23) for the number of hours until arming is to take place. For example if it is 3:00 pm and auto-arming is to take place at 8:00 pm enter 05 for the five hours between 3:00 pm and 8:00 pm. , . . * _ -" . . . The [-K] [S] command is only used to set the arming time. [. . . ] and due to, but not limited to, criminal tampering or electrical disruption. . FCC COMPLIANCE This equipmenl generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufaclurers inslruclions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for class "B" computing device in accordance with the specifications in Subpart "J" of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residenlial installalion. However, lhere is no guarantee that interference will not occur in a particular installation. [. . . ]