User manual DSC PC1575

[. . . ] Instruction Manual PC1575 AVIS: L'étiquette de l'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme à certaines normes de protection, d'exploitation et de sécurité des réseaux de télécommunications. Industrie Canada n'assure toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur. Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise locale de télécommunication. [. . . ] * IMPORTANT NOTE (All Keypads): The Fire, Auxiliary and Panic keys will NOT function unless programmed by the installer. If these keys are in service and the installer has enabled audible feedback, holding down the key for two seconds will cause the keypad sounder to beep indicating that the input has been accepted and transmission is underway. NOTE: If you have a SL-75 keypad, the System light acts as a Trouble, Memory and Bypass indicator. Unlike the other keypads, these conditions will only be represented by the System light. Please keep this in mind when reading other functions in this manual. Display Lights Ready Light (All keypads): If the Ready light is ON, the system is ready for arming. The system cannot be armed unless the Ready light is ON (see "Arming the System" on page 3). Armed Light (All keypads): If the Armed light is ON, the system has been armed successfully. Trouble Light (All keypads): If the Trouble light is ON, see "Viewing Trouble Conditions" on page 11. Memory Light (LED keypads only): Upon disarming, if an alarm has occurred while the system was armed, the Memory light will turn ON (See "Disarming the System" on page 5). Bypass Light (LED keypads only): If the Bypass light is ON, one or more zones are bypassed (See "Zone Bypassing" on page 10). Fire Light (PC5506 keypad only): If the Fire light is ON, a fire alarm has occurred (See "Fire Alarm Operation" on page 13). Program Light (PC5506 keypad only): The Program light will flash when you are programming access codes, or performing other programming functions. If someone is programming at another keypad, the Program light will turn ON to indicate that the system is busy. Y A ST T E ES R Stay Aw ay Chime Rese t Exit Stay Aw ay Chime Reset Exit <> I XT E Message Display Security Station 1 4 Press to select function. TEST SYSTEM WEEKL Y Refer to Instruction Manual for testing instructions. 2 5 3 6 NO IN USE T NOT IN USE NO IN USE T TEST SYSTEM WEEKL Y Refer to Instruction Manual for testing instructions. NO IN USE T NOT IN USE NO IN USE T The Liquid Crystal Display (LCD) displays prompts and system information on two 16 character lines. If "< >" appears, more information can be accessed by using the arrow (< >) keys. Press [>] to advance the display to next function or item of information. Press the keys on the number pad as prompted by the LCD display to view alarms or troubles, to arm and disarm the system and to bypass zones. To select a function press [D]. Important Note: Test system weekly and have any system trouble conditions corrected by your alarm installer. Zone Bypassing The zone bypassing function is used when access is needed to part of the protected area while the system is armed. Zones which are temporarily out of service due to damaged wiring or contacts may be bypassed to allow system arming until repairs can be made. Bypassed zones are automatically cancelled each time the system is disarmed and must be reapplied before the next arming. NOTE: For security reasons, your installer may program the system to prevent you from bypassing certain zones. If you are bypassing a zone due to damaged wiring or contacts, please call a service technician immediately so that the problem can be resolved and your system returned to proper working order. Do not unintentionally bypass zones when you arm your system. To bypass zones from an LED keypad: Start with the system in the Ready state. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Re-orient the receiving antenna. [. . . ]