User manual DSC ESCORT 4580 V1.3

[. . . ] ® Escort4580 v1. 3 · Instruction Manual WARNING: This manual contains information on limitations regarding product use and unction and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart 'B' of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation. [. . . ] For more options, press star. ' To arm the partition, enter your [Access Code]. Please see sections 8-11 of this manual for descriptions of these functions. Accessing Multiple Partitions Access the security system using the steps described in the 'Accessing Your Security System' section of this manual. After the system gives you its status, the system will announce the list of partitions you have access to. To select Partition Two press [2]' 'Partition Three is ready. To select Partition Three press [3]' To select a partition, press the [number key] for that partition. For example, press [1] to select partition 1; press [2] to select partition 2, and so on. After you have selected a partition, the system will announce 'To turn {Partition X} on press [0]. Please see sections 8-11 of this manual for descriptions of these functions. 4 Arming The System S Arming the System 1. Access the security system using the steps described in the 'Accessing Your Security System' section of this manual. Select a partition to arm as described in the 'Accessing Partitions' section of this manual. If the selected partition is ready to be armed, the system will announce: 'To Turn {Partition X} on Enter Your Access code' 3. If the selected partition is not ready to be armed, the system will announce '{Partition X} is open. Secure {Partition X} before turning on. ' When the 'Secure system before turning on' message is heard, ensure that all zones on the partition are secure (close all doors and windows, stop motion in areas covered by motion detectors) before trying to arm the partition. e c t i o n 5 Stay Arming Stay Arming allows you to arm the system and remain on the premises. When the system announces 'To Turn {Partition X} on Enter Your Access code' press [*]. The system will announce 'To turn {Partition X} on without entry delay press [9]' 2. Exit Delay in progress' The selected partition is now armed in the stay mode. Opening the entry/exit door will now sound an immediate alarm. 5 Disarming The System S IMPORTANT If you return to the premises and find that an alarm has occurred while you were away, it is possible that an intruder may still be on the premises. Go to the nearest telephone and contact the authorities. e c t i o n 6 Disarming the System To disarm your security system: 1. Access the security system using the steps described in the 'Accessing Your Security System' section of this manual. Select a partition to disarm as described in the 'Accessing Partitions' section of this manual. If the selected partition is armed, the system will announce '{Partition X} is on. The system will announce 'Turning {Partition X} off' If there were no alarms while the system was armed, the system will announce 'No alarm memory' When the system is disarmed, the Escort4580 may announce additional messages to advise you of the status of the system, or to allow you to select other partitions. 6 If An Alarm Sounds S Fire Alarm Your installer will tell you if fire detection equipment has been installed and activated on your system. [. . . ] Custom products are only warranted to the extent that they do not function upon delivery. performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at DSC's option. Products not covered by this warranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair estimate shall be provided. [. . . ]