User manual DOLMAR PM-4850 PARTS LIST 2006-09

[. . . ] They're ideal for yardwork and greens keeping and especially suitable for occasional use. They offer the latest technology, ergonomic design and high ease of use at a reasonable price. To ensure your own safety and to get the maximum performance out of your DOLMAR brushcutter, we urge you to read this instruction manual carefully before putting the brushcutter into operation and to strictly observe all of the safety regulations!failure to observe these precautions can lead to severe injury or death! Thank you for choosing a DoLMar product! Table of contents EC declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Damaged cutting tools and cutting tools with hairline cracks must not be used any longer under any circumstances. Operate the brushcutter only with the shoulder strap attached, which is to be suitably adjusted before putting the brushcutter into operation. It is essential to adjust the shoulder strap according to the user's size to prevent fatigue during use. Operate the brushcutter in such a manner as to avoid inhalation of the exhaust gases. Do not start or operate the brushcutter in closed rooms (risk of gas poisoning). Perform this cutting work by swinging the brush cutter evenly in half-circles from left to right (15, similar to a scythe). 13 Transport - - when transporting the equipment or moving to another working location, the brushcutter must be switched off in order to avoid unintentionally starting the cutting tool. never transport the brushcutter when the cutting tool is in operation!The tool protection included with the equipment must always be used if the brushcutter is transported over longer distances. Ensure that the brushcutter is safely secured so that no fuel can run out before transporting it in a vehicle. Before shipping the brushcutter, completely empty the fuel tank. 14 15 6 Storage - - The brushcutter must be safely stored in a dry room. If the brushcutter is stored for a long period of time, it should be given a thorough maintenance check and a complete inspection at an authorized DOLMAR service centre. - If the brushcutter is stored for a long period of time, the fuel tank should be completely emptied and the carburetor run dry. Set the right distance between the throttle grip (C/8) and hand grip, and tighten screws (C/4). Place grip (C/6) on shaft tube. - 9 Installing the cutter guard Important: Safety regulations and your own safety make it imperative to use the right cutter guard with a given cutting tool! warning: Use only the cutting tools shown here!It is not permitted to use other cutting tools as this can increase danger of accidents and cause damage to the equipment! Tool/guard combinations for the MS-260 U / MS-330 U / MS-430 U Cutting tool 4-tooth star blade: Part no. 351 504 101 Outside diameter: 30 mm (9"), arbour: 5, 4 mm (1") 2-line trimmer head Part no. 351 504 10 Install the guard extension Tool/guard combinations for the MS-230 C / PM-4850 / MS-330 C Cutting tool 2-line trimmer head Part no. 351 504 10 Install the guard extension Mounting the cutter guard - Hook the hood (a/5) by the cutout (a/1) on the lug (a/2). Insert and tighten bolt (a/3) and nut (a/4). A Mounting the guard extension for use with trimmer head. Attach the guard extension (B/6) supplied with the brushcutter to the upper part of the cutter guard (a/5), bending it to fitthecontouroftheguard. 6 7 B 10 Attach the trimmer line knife (B/7) to the guard extension (B/8) with the bolt (B/6). note: If the trimmer line has been extended (see "Adjusting theline")thetrimmerlineknifeautomaticallycutstheline ends to the same length during use. 8 Mounting the 4-tooth star blade (MS-60 U / MS-330 U / MS-430 U) always switch off the engine and disconnect the spark plug cap before mounting metal cutter blades!Insert the offset screwdriver 4 mm (C/1) through the winding guard and the locking disc into the opening (C/3) in the angular gear (block the winding gear). If necessary turn the mounting disc (C/3) slightly. - Screw down the locknut (C/7) and tighten it by turning the combination wrench counter-clockwise. Position the blade (C/4), thrust washer (C/5)andfinallythe floatingdisc(C/6) as shown. C Unscrew the locknut (C/7) from the shaft by turning it clockwise. [. . . ] Make contact only with the cylinder (otherwise you may damage the engine). Firmly connect the spark plug cap to the spark plug (removed from the engine) and hold it against the wrench using insulated pliers (away from the spark plug hole!). Pull the starter cable hard. C - - A spark should be visible at the electrode gap. 17 Lubricating the gear box Suction head in the fuel tank D After about 50 operating hours the gear box (D/8) should be checked by a OLMAR service centre, and if necessary regrease. The service centre will add the exact amount of grease, as excessive grease will lead to overheating of the gearbox. E Thefeltfilter(E/9)ofthesuctionheadisusedtofilterthefuel taken in by the carburetor. [. . . ]