User manual DOLMAR HT-140 PARTS LIST 1-01

[. . . ] Please read, understand and follow this booklet which refers in detail to the various points that will demonstrate its outstanding performance. This will assist you to safely obtain the best possible results from your DOLMAR Hedge trimmer. It is very important to understand the following symbols when reading this instructions manual. Keep the area of operation clear of all persons and pets Wear eye and ear protection Read the Instructions carefully for the correct handling, preparation, maintenance, starting and stopping of the machine. [. . . ] Do not perform any modifications to the Hedge Trimmer as this will risk your safety. The performance of maintenance or repair work by the user is limited to those activities as described in this instruction manual. Use only genuine spare parts and accessories supplied by DOLMAR authorized or factory service centers. Use of non-approved accessories and tools means increased risk of accidents and injuries. DOLMAR will not accept any liability for accidents or damage caused by the use of any non-approved accessories. In case of an accident make sure that a well-stocked first-aid kit according to DIN 13164, is available in the vicinity of the cutting operations. When asking for help, please give the following information: - Place of accident - What happened - Number of injured persons - Extend of injuries - Your name Cardboard is a basic raw material and is therefore consequently reusable or suitable for recycling (waste paper recycling). Petrol Hedge Trimmer: model HT-2460, HT-140 (See TECHNICAL DATA for the specifications) We declare under our sole responsibility that this product is in compliance with the following Directives, 2000/14/EC, 2006/42/EC. The most important standards applied to properly meet the requirements of the above Directives were: ISO 10517. 7 dB (A) Guarantee Sound Power: 105 dB (A) These sound power levels wear measured in accordance with Council Directive, 2000/14/EC. HT-2460 Model Dimension (L x W x H) Mass (without blade cover) Volume (fuel tank) Engine displacement Cutting length Maximum engine performance Maximum blade speed Idling speed Clutch engagement speed Carburetor type Ignition system Spark plug Electrode gap Right handle Vibration per ISO 10517 Left handle ahv eq Uncertainty K ahv eq Uncertainty K mm kg L cm Sound pressure level average according to ISO 10517 Sound power level according to ISO 10517 Mixture ratio (fuel: DOLMAR 2-stroke engine oil) Gear ratio 1) The data takes equally into account the idling and racing speed operating modes. Check the cutting device is not damaged, the control lever for easy action and check for proper function of the I-O Switch. (See Starting) - Start the hedge Trimmer engine only after the entire assembly is done. Operation of the engine is only permitted after all the appropriate accessories are attached. - Before starting, make sure that the cutting device has no contact with objects such as branches, stones, etc. - Before trimming, inspect area for wires, cords, glass, or other foreign objects which could come in contact with the blade. Place the Hedge Trimmer on a clean area of ground make sure that the cutting tool does not come into contact with the ground or any other objects. Cold starting: (When the engine is cold or it has been stopped for more than 5 minutes or when fuel is added to the engine. Give a gentle push on the primer pump (2) repeatedly (7 to 10 times) until fuel comes into the primer pump. Hold the unit down firmly so you will not lose control while cranking the engine. - Always hold the Hedge Trimmer firmly with both hands on the handles only. - When you release the throttle, it takes a few moments before the cutting blades stop. [. . . ] - If necessary, correct it by means of the idle screw (the cutting blade must not run when the engine is on idle). Counter-clockwise: for slower rate of revolution Check that there is sufficient difference between idling and clutch engagement speed to ensure that the cutting tool is at a standstill while the engine is idling. ) If the tool still continues to run under the idling conditions, consult your nearest authorized service agent. DANGER: INFLAMMABLES STRICTLY PROHIBITED Interval of Cleaning and Inspection: Daily (every 10 operating hours) - Turn the choke lever to the full close side, and keep the carburetor off from dust or dirt. [. . . ]