User manual DOLMAR ES-2135 A

[. . . ] Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations!Keep this instruction manual! ES-2130 A ES-2135 A ES-2140 A ES-2145 A http://www. dolmar. com Thank you for your trust in our product We congratulate you on your new DOLMAR electric chain saw. We are convinced that you will be satisÞed with this modern machine. DOLMAR electric chain saws are characterized by their robust, high-efÞciency motors and high chain velocities which allow an excellent cutting efÞciency. [. . . ] Observe the accident prevention instructions issued by the competent trade federations and insurance companies. Perform only the maintenance and repair works described in the instruction manual. Applying spare parts which are not original DOLMAR parts or accesories and bar/chain combinations or lengths results in a high risk of accidents. For accidents and damage resulting from using sawing devices or accesories which have not been approved we cannot accept any responsibility. For the event of a possible accident, please, make sure that a Þrst aid box is always immediately available close by. Should you ask for help, please, give the following information: - place of accident - what happened - number of injured persons - kind of injuries - your name. NOTE Individuals with poor circulation who are exposed to excessive vibration may experience injury to blood vessels or the nervous system. Vibration may cause the following symptoms to occur in the Þngers, hands or wrists: "Falling asleep" (numbness), tingling, pain, stabbing sensation, alteration of skin colour or of the skin. If any of these symptoms occur, see a physician! 8 - - - 20 Maintenance - - 21 - 22 First aid SERVICE 23 24 Technical data Power consumption Nominal voltage Mains frequency Nominal current Fuse, electric circuit Cable length Chain type Chain pitch Length of a cut Max. chain speed per EN 60745-2-13 ES-2130 A Watt V Hz A A cm inch cm m/s dB (A) ES-2135 A 2000 230 - 240 ~ 50 - 60 8, 8 16 30 / 500 092 3/8" ES-2140 A ES-2145 A 30 35 13, 3 101, 8 90, 8 40 45 Sound power level LWA av Sound pressure level LpA av dB (A) at the workplace per EN 60745-2-13 Vibration acceleration ah, w av per EN 60745-2-13 - Tubular handle m/s2 - Rear handle m/s2 Oil pump Oil tank capacity ml Power transmission Overload protection Chain brake Run-out brake Weight (without bar/chain) kg kg Weight (with bar/chain) Radio interference suppression / EMC Protective case Extension cable (not included) 5, 0 4, 7 5, 6 automatic 140 direct electrical manually actuated electrical 4, 4 5, 1 5, 2 Per EMC Directive 2004/108/EG class II (double protective insulation) DIN 57282/ HO 7RN-F L= 30 m max. , 3x1, 5 mm2 5, 3 1 Denomination of components 2 3 Figure: IdentiÞcation plate ES-2145A 2008 123456 Serial number Year of manufacture 7 6 5 4 230-240 V~ 50-60 Hz 8. 8 A 2000 W GB Typ 226 XXX XXX XXX 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Tubular handle Hand guard (release for chain brake) Spike bar Sprocket guard quick tightener Sprocket guard, chain brake Carbon brush cover Back hand guard Power cord with plug Guide bar Oil tank cap IdentiÞcation plate Locking button Rear handle Power switch Sightglass for oil level Saw chain Cord grip for electric cord (pull relief) 8 Indicate when ordering spare parts! 9 10 11 12 13 17 16 15 14 9 PUTTING INTO OPERATION CAUTION: When working on the guide bar or saw chain always wear protective gloves and pull out the power supply plug. CAUTION: Switch on the electric chain saw only after having assembled it completely and inspected! A Mounting the guide bar and saw chain Put the electric chain saw on a stable surface and carry out the following operations for mounting the bar and chain: Release chain brake. To do this, pull the hand guard (1) in the direction of the arrow. 1 4 Flip up the sprocket guard quick tightener (2) (see also Fig. Push in the sprocket guard quick tightener Þrmly against spring pressure, and slowly turn it counter-clockwise until you feel it engage. Release the sprocket guard quick tightener (remove pressure) and now turn it clockwise to its original position. Pull the sprocket guard (3) up slightly, pull out of the rear Þttings (4) and remove. 2 3 B Position the guide bar (7) and push it against the sprocket (6). 6 7 C Place the saw chain (9) on the sprocket (6). Using your right hand, guide the saw chain into the upper guide groove (8) of the guide bar. The cutting edges of the saw chain on the top of the guide bar must point in the direction of the arrow! D 10 6 9 8 Using your left hand, lightly press the guide bar against the holder on the housing and guide the saw chain (9) around the nose sprocket (10) on the guide bar. While doing this, pull the saw chain slightly in the direction shown by the arrow. 9 10 E Line up the hole in the sprocket guard with the threaded pin (11). Turn the chain tensioning screw (H/14) to align the chain tensioning pin (12) with the hole in the guide bar. 11 12 3 F First press the sprocket guard (3) into the mounting (13) and then push it onto the threaded pin (11). 13 3 G Tightening the saw chain Firmly push in and simultaneously turn the sprocket guard quick tightener (2, clockwise) in order to screw on the sprocket guard (3), but do not tighten it yet. Lift the tip of the guide bar slightly and turn the chain tensioner (14) clockwise until the saw chain engages in the guide groove on the lower side of the guide bar (see the circle). Push in the sprocket guard quick tightener (2) again and tighten by turning clockwise. 2 14 2 Release the sprocket guard quick tightener (2) (remove pressure) until it turns freely, then fold it in as shown in the illustration. H 11 Checking the chain tension The chain has the proper tension when it lies against the bottom edge of the guide bar and can be easily pulled by hand about 2-4 mm (about 1/8") up from the guide bar. Check the chain tension frequently - new chains tend to get longer during use! [. . . ] He will also have the relative spare part lists to determine the required spare part numbers, and will be constantly informed about the latest improvements and also about spare part innovations. To Þnd your local distributor, please visit www. dolmar. com Please, take in mind that in the case that foreign spare parts are used instead of the original DOLMAR spare parts this will automatically invalidate the DOLMAR product guarantee. Guarantee DOLMAR guarantees the highest quality and will therefore reimburse all costs for mending through replacement of damaged parts as a result of material or production faults, which occur within the guarantee time after purchase. Please, note that in some countries particular guarantee conditions may exist. In case of any doubts, please, contact your salesman who is responsible for the guarantee of the product. [. . . ]