User manual CATEYE CC-RD100

[. . . ] Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to our service shall be borne by person desiring service. CO. , LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: CATEYE Customer Service Section Service & Research Address for USA CATEYE Service and Research Center 1705 14th St. 115 Boulder, CO 80302 Phone: 303. 443. 4595 Toll Free: 800. 5CATEYE Fax: 303. 473. 0006 E-mail: service@cateye. com URL: http: //www. cateye. com C F B D E 1 AC H G MENU b 1 a ! 1 CLICK 2 Push! 1 a b for STEM for HANDLEBAR 2 9 ! A MODE 4 6 9 5 7 2 A SENSOR LINE 2 1 2 1 3 8 2 8 4 SENSOR LINE Component name 1 2 3 4 5 6 7 8 9 Bracket band Bracket Sensor Magnet Sensor rubber band (x2) Sensor hook Sensor rubber pad (x3) Nylon ties (x5) Bracket rubber pad B Max. [. . . ] Then enter the total distance, previously noted, via Odo Input in the SETTING MENU. Lithium Battery CR1620 X 1 Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 year (Using the battery for one hour a day; the battery life will vary with the conditions of use. ) Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-bit 1-chip microcomputer (Crystal controlled oscillator) Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0100 mm ­ 3999 mm (Default figure A : 2096 mm, B : 2096 mm) Working temperature . . . . . . . . . . . . . . 0°C - 40°C (32°F - 104°F) Dimension/Weight . . . . . . . . . . . . . . . . . . . 1-53/64" x 1-7/32" x 19/32" (46. 5 x 31 x 15 mm) / 0. 63 oz (18 g) * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice. If the computer has not received any signal for an hour, power-saving mode will activate and only the clock will be displayed. Alternatively, if the sensor detects a signal or the MODE button is pressed, the main display reappears. Specification Dual Wheel Size Two wheel sizes ( and ) can be registered on the computer. This is useful when the computer is shared between two bicycles or when different wheel sizes are used on the same bicycle but at different times. To bring up the menu screen, press the MENU button with the Measuring screen displayed. With the menu screen displayed, press and hold the MODE button to change the setting for the display menu. If the menu screen is not touched for a minute, the Measuring screen reappears. The new settings are applied only when the SET button (Finishi) is pressed. Press the MODE button to switch between functions displayed in the following order: A or B Wheel Size: HOLD the MODE button and A or B begins to flash. Find your tire size off the front tire and match to the circumference chart (part 3 of SET-UP CHART). Press the MODE button to switch between "24H" and "12H". When the Hour is correct HOLD the MODE button and minutes will begin to flash. When the time is correct press the MENU button to return to the "menu loop". When the desired speed scale is flashing, press the MENU button to set and return to the "menu loop". [. . . ] When the desired speed scale is flashing, press the MENU button to set. Tire Circumference: Find the size of your front tire and match to the tire circumference chart (part 3 of SET-UP CHART). Repeat until finished and then press the MENU button to set the tire circumference. Clock Setting: HOLD the MODE button for two seconds and "24h" will flash. [. . . ]