User manual BOSS RAGE REV785
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSS RAGE REV785. We hope that this BOSS RAGE REV785 user guide will be useful to you.
Manual abstract: user guide BOSS RAGE REV785
Detailed instructions for use are in the User's Guide.
[. . . ] Dangerous high voltages are present which may result in electric shock. · To avoid risk of electronic shock or damage to the amplifier, do not permit any of this equipment to become damp or wet from water or drinks. If this does occur, immediately unplug the power wires and send the amplifier to your local dealer or service center as soon as possible. · If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures, immediately unplug the power cord and send the amplifier to your local dealer or service center as soon as possible .
Installation precautions
Before you drill or cut any holes, investigate your car's layout very carefully. [. . . ] · If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures, immediately unplug the power cord and send the amplifier to your local dealer or service center as soon as possible .
Installation precautions
Before you drill or cut any holes, investigate your car's layout very carefully. Take special care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring. Attach all audio system components securely to prevent damage, especially in an accident. Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer's warranty.
SHOCK HAZARD!There are no user-serviceable parts within the unit.
CHAOS WIRED Amplifier User's Manual - page 4
Mounting the amplifier
1. Find a suitable location in the vehicle in which to mount the amplifier. Make sure there is sufficient air circulation around the intended mounting location. Ignoring these instructions will result in an input overload to the amplifier, and excessive audio distortion. It can also cause the protection circuit to engage.
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time!
2-Channel Amplifier
CW150
To Audio Outputs of head unit or signal processor
4-Channel Amplifier
CW350
To Audio Outputs of head unit or signal processor
CHAOS WIRED Amplifier User's Manual - page 7
High Level Input Wiring, cont.
The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time!
2-Channel Amplifier
CW150
R+ R- L- L+
To Speaker Terminals of head unit
4-Channel Amplifier
CW350
CH4+
CH3CH3+
CH2+
CH1CH1+
CH4-
CH2-
To Speaker Terminals of head unit
CHAOS WIRED Amplifier User's Manual - page 8
Power and Speaker Wiring
2-Channel Amplifier
CW150
+ +
RIGHT Speaker
LEFT Speaker
SPEAKER IMPEDANCE 2-8 OHMS
Chassis ground point
to REMOTE TURN-ON terminal of head unit
4-Channel Amplifier
CW350
CH1 Speaker
FUSE
Battery
CH2 Speaker
SPEAKER IMPEDANCE 2-8 OHMS
CH4 Speaker
Chassis ground point
to REMOTE TURN-ON terminal of head unit
SPEAKER IMPEDANCE 2-8 OHMS
CH3 Speaker
FUSE
Battery
CHAOS WIRED Amplifier User's Manual - page 9
Troubleshooting
If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. POSSIBLE REMEDY
Check to make sure you have a good ground connection. If the Protection LED still comes on, then the amplifier is faulty and needs servicing. If the hiss disappears, then plug in the component driving the amplifier and unplug its inputs. If the hiss disappears at this point, go on until the faulty/noisy component is found. [. . . ] If the Protection LED still comes on, then the amplifier is faulty and needs servicing. If the hiss disappears, then plug in the component driving the amplifier and unplug its inputs. If the hiss disappears at this point, go on until the faulty/noisy component is found. It is best to set the amplifier's input level control as low as possible. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSS RAGE REV785
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSS RAGE REV785 will begin.