User manual BOSCH WVD24520ME

[. . . ] Maxx 5 Washerdryer en Operating and Installation Instructions Table of Contents Operating instructions Information concerning waste disposal . 4 5 6 7 13 14 20 22 28 31 37 39 41 43 48 52 53 54 Installation instructions Installing, connecting and transporting . . 2 The new washer dryer which you have just purchased is a modern, high quality domestic appliance. Your washer dryer is distinguished by its economical consumption of energy, water and detergent. [. . . ] The steps for changing the settings are described in detail overleaf. Overview at a glance Turn on the tap, load the laundry and close the loading door. Select desired washing/drying programme with programme selector. °C Temp. * Page 32 or cold wash B Spin speed* Page 32 or without final spin W Finish in time* Page 33 can be set in 1-hour steps Signal* Page 36 on off loudness Make further settings or press the Start/Pause M button. Childproof lock** Page 35 on off * Individual settings can be combined. **This function is recommended to avoid misoperation by casual touching. 31 Washing temperature You can change the default washing temperature. q Keep touching the temperature button until the desired temperature displays. Temp. i For different clothing, there are different programmes with respective temperature ranges. Spin speed You can change the default spin speed. i If setting (without final spin) has been selected, the washing remains in the final rinsing water. Before the laundry can be uplaoded, the Empty b or Spin B programme must be performed. Touch Spin B button to select the desired spin speed or touch the Start/Pause M button directly to start subsequent spin cycle with default spin speed. i The speed can be changed at any time by touching the Spin B button until the new speed is displayed. Setting "" (without final spin) is possible until the Rinse programme section starts. 32 Finish in time Example of Easy Care 40 ºC programme: Before a programme starts, you can specify by how many hours later the programme is to be ended. q Touch the W Finish in button, the display shows the minimum finish in time of the selected programme. It depends on the duration of selected programme. q Touch the W Finish in button until the desired number of hours is displayed. If a finish in time of 24h has been set, the programme duration mode can be accessed by touching the W Finish in button again. When the finish in time has elapsed, the programme starts automatically and the programme duration is displayed. - Touch the Start/Pause M button directly to start the programme immediately. - Touch the Start/Pause M button. 33 i If the programme sequence is changed by rotating the programme selector or the programme is cancelled, the preselected finish in time is also cancelled. The programme duration of the newly selected programme appears in the display. The finish in time must be reselected (see also chapter Changing the programme, page 37 and Cancelling the programme, page 37). Close the washer dryer door. 34 Childproof lock You can secure your washer dryer to prevent selected functions from being inadvertently changed. If the childproof lock has been selected: - no changes can be made while the programme is running, - the symbol G flashes if a programme setting is inadvertently changed, - should the appliance be switched off and on while a programme is running, the programme will continue at the point at which it was interrupted, - when the programme ends, the duration time is showed as 0:01, the loading door cannot be opened, deactivate the childproof lock, the door can be opened while the display shows 0 . Activating the childproof lock q Set the programme selector to the required programme and, if required, select other settings. i Release the Start/Pause M button. Example of Easy Care 40 ºC programme: q Touch the W button and hold down (for approx. q Release the W button, the childproof lock is activated, the symbol is permanently on. Deactivating the childproof lock The childproof lock must be deactivated before making programme changes or ending programmes. [. . . ] 2. 20 m). 58 m ax. 100 cm ~150cm Connecting the water Water inlet hose d Risk of electric shock!To prevent leaks or water damage, it is essential to follow the instructions in this chapter!Do not connect to the mixer tap of an unpressurised hot water apparatus. Only use the inlet hose supplied or one which was purchased from an authorised specialist dealer. [. . . ]