User manual BOSCH SGV 5603-03

[. . . ] The hoops (if fitted) consist of polypropylene (PP). Installation Install and connect the appliance according to the installation and assembly instructions. The dishwasher must NOT be connected to the power supply during installation. Ensure that the protective conductor system of the domestic electricity supply has been installed correctly. Electrical connection conditions must correspond with the specifications on the rating plate of the dishwasher. [. . . ] The rinse programme is automatically adjusted in order to obtain the best possible rinsing and drying result. Observe the following important information if using combined cleaning products: Regeneration salt is not required up to a water hardness of 21_ dH (37_ fH, 26_ Clarke, 3. 7 mmol/l) only. Salt is still required if the water hardness is above 21_ dH (37_ fH, 26_ Clarke, 3. 7 mmol/l). The factory-set hardness setting "hardness auto" ensures that the water softening system is set optimally by the optical limescale sensor even if combined cleaning products are used. < Auto Wash > After switching on the Main Menu shows the programme "Auto Wash". Setting the Programme From the programme "Auto Wash" in the Main Menu you can select among the following programmes: "Auto Super Wash" ­ "Auto Wash" ­ "Auto Delicate Wash" ­ "Short Rinse" ­ "Prerinse Only". The auto programmes "Auto Super Wash", "Auto Wash", and "Auto Delicate Wash" automatically match the programme to the amount and soil level of the dishes. Using the following programme overview you can select the appropriate programme for the type, amount, and soil level of the dishes. 19 en If in doubt, please contact the detergent manufacturer, especially if: the utensils are very wet at the end of the programme. Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of salt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness. If the "Add rinse aid or special salt" display is defective, you can switch it off as follows: Switching "Add special salt" and therefore the water softening system off and on: Switch on the appliance with the main switch 1 . Keep pressing button M/OK 2 until the "hardness auto" setting is displayed. By pressing buttons ­ or + 3 , select a set value between 0 (off) and 7. Alternatively, you can choose "Save Drying" or "Extra Drying". The option "Extra Drying" increases the temperature during rinsing in all programmes. (Please take care with delicate dishes. ) Remote Control ** After choosing the option "Remote Control" the display will show "Remote Control: Off" (factory setting) You activate this option by selecting "Remote Control: On". ** Only with installed interface Buzzer Volume You can modify the volume of the acoustic signals or even turn it off altogether. If the option "Buzzer Volume" is chosen the display shows "Buzzer 6" (factory setting). You can change this value to 0 (acoustic signals switched off) or to values between 1 (quiet) and 6 (loud). A short buzz demonstrates the currently chosen volume level. 23 en Adding Rinse Aid You can set the amount of rinse aid added. If the option "Adding Rinse Aid" is chosen the display shows "Rinse Aid 4" (factory setting). Change this setting only if there are streaks (reduce the value) or water stains (increase the value) remaining on the dishes. You can choose a value between 0 and 6. Language You can change the language selected when the appliance was started for the first time (see chapter "Before Starting The Device For The First Time"). If the option "Language" is chosen the display shows several language abbreviations. [. . . ] If the appliance is not connected via a plug, the installation side must feature an all-pole disconnector with a contact gap of at least 3 mm in order to satisfy the relevant safety regulations. Installation The dishwasher must be connected by a qualified technician to ensure correct operation. The specifications for supply, drainage and connected load must fulfil the required criteria as stated in the following paragraphs or in the installation instructions. Install the appliance in the following sequence: ­ Check the delivery ­ Install the appliance ­ Connect the waste water ­ Connect the fresh water ­ Connect the power supply Delivery Your dishwasher was checked at the factory to ensure that it was in perfect working order. These will disappear after the first rinse cycle. Installation The required installation dimensions can be found in the installation instructions. [. . . ]