User manual BOSCH PSB 12 VE-2

[. . . ] B) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Never use the cord for carrying, pulling or unplugging the power tool. E) When operating a power tool outdoors, use an extension cord suitable for outdoor use. [. . . ] English | 19 g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. 20 | English Products sold in GB only: Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362). If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. the replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere. Products sold in AUS and NZ only: Use a residual current device (RCD) with a rated residual current of 30 mA or less. 11 Extraction device with dust collector * 12 Dust collector* 13 Level indicator of the dust collector * 14 Thumbwheel for speed preselection (PSB 650 RE/PSB 6500 RE/PSB 650 RA) 15 Handle (insulated gripping surface) 16 Release button for dust collector * 17 Filter element (Microfilter System) * 18 Rubber gasket for dust collector * 19 Dust protection ring* 20 Release button for extraction device * 21 Clamp for extraction device * 22 Locking latch for dust collector* 23 Universal bit holder* 24 Screwdriver bit* 25 Spindle lock button (PSB 650 RE/PSB 6500 RE/PSB 650 RA) 26 Allen key ** *Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of accessories can be found in our accessories program. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. The machine is intended for impact drilling in brick, concrete and stone as well as for drilling in wood, metal and plastic. Machines with electronic control and right/left rotation are also suitable for screwdriving and thread-cutting. ­ The dust protection ring 19 can wear, especially when working with large drill-bit diameters. Mounting the Extraction Device (see figure A) Guide the extraction device 11 from the front toward the bottom side of the impact drill. Pay attention that the extraction device 11 faces flush against the casing and that it is locked. 24 | English When the extraction force diminishes or when the level indicator 13 is full, the dust collector 12 must be emptied. For this, press on the riffled surface of the release button 16 and take off the dust collector 12. When placing on the holder again, make sure that the rubber gasket 18 is inserted. Reattach the dust collector 12 again and lock it by pressing against the smooth surface of the release button 16. Removing the Extraction Device (see figure E) For disassembly of the extraction device 11, press release button 20 and pull off the extraction device 11 toward the front. Stowing the Extraction Device (see figure F) For stowing the extraction device 11 in the case, remove the extraction device 11, slide it together and attach clamp 21. Attach the locking latch 22 or empty the dust collector 12 before placing down the extraction device. Pull out the depth stop until the distance between the tip of the drill bit and the tip of the depth stop correspond with the desired drilling depth X. [. . . ] The auxiliary handle 9 can be set to any position for a secure and low-fatigue working posture. Removing the Drill Chuck (see figure L) Clamp the short end of an Allen key 26 into the keyless chuck 2. Hold the machine firmly, press the spindle lock button 25 and loosen the keyless chuck 2 by turning the Allen key 26 in rotation direction . Loosen a tight keyless chuck by giving the long end of the Allen key 26 a light blow. [. . . ]