User manual BOSCH DIB09E850B INSTALLATION INSTRUCTIONS

[. . . ] 7 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pipe dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Preparing the ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Attaching flue duct. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 INSTRUCTION MANUAL Additional information on products, accessories, replacement parts and services can be found at www. bosch-home. com and in the online shop www. bosch-eshop. com Produktinfo Environmental protection This appliance is labelled in accordance with the European Directive 2002/96/EU concerning used electrical and electronic appliances (WEEE ­ waste electrical and electronic equipment). [. . . ] The different options of operating the appliance in circulating-air mode can be found in the brochure or ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use. Operation These instructions apply to several appliance models. It is possible that individual features are described which do not apply to your appliance. Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. Control panel variant 1 Switching on fan: variant 1 Press On/Off button. Increase fan setting by pressing button @ or reduce it by pressing button A. Intensive setting You can use the Intensive setting for particularly strong odour and fume generation. You can always switch back manually. 2Q2II 'LVSOD\ IDQ VHWWLQJV /LJKW 2Q2II Switching on fan: variants 2 and 3 Increase or reduce the fan settings by pressing buttons 1, 2 and 3. Intensive setting: variant 3 Press button ~. 5HGXFH IDQ VSHHG Control panel variant 2 , QFUHDVH IDQ VSHHG , QWHQVLYH VHWWLQJ Light The light can be switched on and off independently of the fan. /LJKW 2Q2II Control panel variant 3 )DQ VHWWLQJV /LJKW 2Q2II 4 )DQ VHWWLQJV 3 , QWHQVLYH VHWWLQJ Installing and removing filter ã=Risk of burns, risk of electric shock! from appliance. Pull metal-mesh grease filter downwards. In doing so, place other hand under the metal-mesh grease filter. 2. Take metal-mesh grease filter out of the holder. Removing metal-mesh grease filter 1. Open lock and fold down the metal-mesh grease filter. Notes In doing so, place other hand under the metal-mesh grease filter. 2. The metal-mesh greases filter must not be wedged in. Clean the surfaces with a soft, damp cloth, washing-up liquid or a mild window cleaner. Dry cloths, abrasive sponges, scouring agents, cleaning agents containing sand, soda, acid, chlorine or any other aggressive substances are not suitable. Clean the stainless steel surfaces in the direction of the ground surface only. Do not use stainless steel cleaner or wet cloths for the controls. By hand: Note: You can use a special grease solvent for stubborn dirt. It can be ordered via the Online Shop. Soak the metal-mesh grease filters in a hot soapy solution. Leave the metal-mesh grease filters to drain. 5 Replacing bulbs ã=Risk of burns, risk of electric shock! from defective bulbs. Always replace defective bulbs immediately (leave bulbs to cool down first) to prevent the remaining bulbs from overloading. Use only bulb of the same type and same power (see bulb holder or rating plate inside the appliance) ­ to do this remove metal-mesh grease filter. Replacing filament bulbs 1. Lift bulb cover slightly and push towards the outside of the appliance. 2. [. . . ] Attach the earthed socket preferably inside the flue duct. Note: Ensure that the mains cable is not trapped. 2. Attach the appliance to the support frame using 2 securing screws. [ The earthed socket should be connected via its own circuit. If the earthed socket is no longer accessible following installation of the appliance, a disconnector must be fitted as for a permanent connection. If a permanent connection is required, the installation must feature an all-pole disconnector (circuit breakers, fuses and contactors) with a min. The permanent connection may be installed by an electrician only. 3. [. . . ]